Abstract:AA2060-T8 is a relatively new Al-Cu-Li alloy developed in the last few years as a lightweight alternative to conventional Al alloys. Thus, it is essential to characterize the warm flow, fracture, and anisotropic behaviours of this alloy and propose constitutive analysis-based crystal plasticity (CP) modelling to link its mechanical behaviour with the microstructural state. Therefore, in this study, isothermal warm tensile tests were conducted using a Gleeble-3800 thermomechanical simulator and different sample orientations at temperatures and strain rates varying from 373 to 573 K and 0.001 to 0.1 s −1 , respectively. The tensile behaviour of the 2060 Al-Cu-Li alloy sheet depends on the sample orientations, which results in significant anisotropy. The anisotropic degree of the tensile properties of this alloy was significantly reduced by increasing the forming temperature above 473 K. In addition, the fracture behaviours of 2060 Al-Cu-Li sheets were transformed from mixed ductile-brittle fracture mode to ductile fracture mode by decreasing strain rates and increasing the temperatures, respectively. Afterward, a novel crystal plasticity model was proposed to describe the grain behaviour and the deformation mechanism of 2060 Al-Cu-Li alloy under warm forming conditions. The developed constitutive model was implemented using the monolithic time-integration algorithm-based backward Euler method. The results acquired from the proposed constitutive analysis agree well with those obtained from experimentation in all testing conditions. This indicates its ability to accurately predict the warm flow behaviour of 2060 Al-Cu-Li alloy under different strain rates and loading directions.

Constitutive Behavior Predictions of Mushy Zone During Solidification by Phase Field Model and Coupled Eulerian–Lagrangian Method

Phase Field Simulation for Non-Isothermal Solidification of Multicomponent Alloys Coupled with Thermodynamics Database

Prediction of Mushy Zone Permeability of Al-4.5wt%Cu Alloy During Solidification by Phase Field Model and CFD Simulation

Constitutive modeling of mechanical behaviors in gradient nanostructured alloys with hierarchical dual-phased microstructures

Prediction of the Equivalent Elastic Modulus of Mush Zone During Solidification Process Coupled with Phase Field Simulations

An Integrated Approach to Study the Hot Tearing Behavior by Coupling the Microscale Phase Field Model and Macroscale Casting Simulations

Phase-field Model Simulations of Alloy Directional Solidification and Seaweed-Like Microstructure Evolution Based on Adaptive Finite Element Method

Zone Partitioning Sequential Calculation Method for Three-Dimensional Phase-Field Material Simulation During Directional Solidification

Phase-field model of isothermal solidification in multicomponent alloys for multiple grains

Prediction of permeability in mushy zone of Al-4.5 %Mg alloy based on CA-LBM model

Mechanical Behavior of Mushy Zone in DC casting using a Viscoplastic Material Model

Cfd-Based Multicomponent Model for Solidification of Casting Process

Predicting the constitutive behavior of semi-solids via a direct finite element simulation: application to AA5182

Mathematical Model of Unidirectional Solidification with Mushy Layer

Phase-Field Simulation of Microsegregation and Dendritic Growth During Solidification of Hypoeutectic Al-Cu alloys

A Thermomechanical Finite Element Model for Simulating the Solidification Process of Squeeze Casting

An Experimental Study of Deformation of a Columnar Dendritic Mushy Zone Using a Transparent Succinonitrile-Acetone Alloy

The Flow Stress Behavior and Physical-Based Constitutive Model for As-Quenched Al-Zn-Mg-Cu Alloy

INTEGRATED FINITE ELEMENT MODEL FOR TRANSIENT FLUID FLOW AND THERMAL STRESSES DURING CONTINUOUS CASTING

Unified Wave Equation and Numerical Simulation of Mechanical Wave Propagation in Alloy Solidification

Characterization and constitutive analysis-based crystal plasticity of warm flow and fracture behaviours of 2060 Al-Cu-Li alloy