Abstract:The smooth particle hydrodynamics (SPH) method is advantageous in tracking a free surface and a moving interface. This paper uses the SPH method to simulate the filling process of squeeze casting. The simulated temperature field at the end of filling was input into a finite element model (FEM) program to simulate the solidification process after squeeze casting. Due to the existence of a liquid phase, a solid phase, and a two-phase mushy zone in the solidification process after squeeze casting, the deformation behavior in the solidification process was modeled with a thermoelasto–viscoplastic constitutive model representing these different phases. In the RDG thermal cracking criterion based on the principle of dendrite gap complement, there are a strain rate term, a secondary dendritic spacing term, and a pressure term. These terms accurately describe the squeeze casting process. Therefore, the RDG criterion was used to predict thermal cracking. The strain rate term in the RDG criterion was calculated by the FEM. For the calculation of the secondary dendritic spacing, the temperature field during the solidification process is locally refined by the FDM method to complete the transition from the macroscale to the mesoscale; then the refinement results are imported into the phase field method for dendritic growth simulation. The results show that the method based on multi-model coupling has satisfactory prediction accuracy for the thermal cracking in the squeeze casting process. The combination of the phase field method and the RDG criterion provides a new approach to the simulation of thermal cracking defects. The prediction results show that the thermal cracking tendency increases with an increase in strain rate. However, the local position C of the bracket sample had a higher strain rate of 7.15/s, and a lower cooling rate of 2.96 K/s offset the effect of the high strain rate. As a result, a low thermal cracking tendency level of 1.13729 was obtained.

Mechanical Behavior of Mushy Zone in DC casting using a Viscoplastic Material Model

An Integrated Approach to Study the Hot Tearing Behavior by Coupling the Microscale Phase Field Model and Macroscale Casting Simulations

Analyses of Constitutive Behavior of As-Cast Aluminum Alloys AA3104, AA5182, and AA6111 During Direct Chill Casting Using Physically Based Models

Constitutive Behavior Predictions of Mushy Zone During Solidification by Phase Field Model and Coupled Eulerian–Lagrangian Method

Effects of cooling rates on microporosity in DC casting Al-Li alloy

Thermomechanical Modeling of Solidification Process of Squeeze Casting I. Mathematic Model and Solution Methodology

Mechanical Properties and Fracture Behaviors of a Non-heat-treated Alloy in Varied Regions Within a Megacasting

Continuous Casting Mould for Square Steel Billet Optimised by Solidification Shrinkage Simulation

Study on Mushy Zone Coefficient in Solidification Heat Transfer Mathematical Model of Thin Slab with High Casting Speed

Thermal cracking prediction for a squeeze casting process with an approach of multi-scale and multi-model coupling

Microstructure simulation in pressurized solidification during squeeze casting of aluminum alloy A356

A Study on the Numerical Simulation of Thermal Stress During the Solidification of Shaped Castings

Numerical Simulation of the Thermo-Mechanical Process for Beam Blank Continuous Casting

A Mathematical Model for Simulating the Microporosity of Squeeze Casting of Aluminum Alloy

A Thermomechanical Finite Element Model for Simulating the Solidification Process of Squeeze Casting

3-D Mathematical Modeling of the Effect of Shunt Plate Hole Distribution and Magnetic Field on Transport Phenomena Within DC Casting of Magnesium Alloy Slab

AN ELASTIC-VISCOPLASTIC CONSTITUTIVE MODEL FOR SQUEEZE CASTING ALUMINUM ALLOY

Phase-Field Modeling of Coupled Brittle-Ductile Fracture in Aluminum Alloys

Domination and Effect of Multi-parameters in Direct Chill Casting based on Establishment of Thermo Model by Numerical Simulation and Experiment

Prediction of Mushy Zone Permeability of Al-4.5wt%Cu Alloy During Solidification by Phase Field Model and CFD Simulation

Heat, Mass and Momentum Transport Behaviors in Directionally Solidifying Blade-Like Castings in Different Electromagnetic Fields Described Using a Continuum Model