Abstract:Silica aerogels generally exhibit poor mechanical properties, which seriously restrict their commercial use and makes it necessary to reinforce their structures to obtain materials strong enough to withstand mechanical stresses. The incorporation of polymers into silica aerogels is a promising approach due to the enhancement in mechanical strength afforded and the possibility of imparting the hydrophobicity of the polymers to the resulting aerogels. However, the processes typically employed to prepare polymer-reinforced silica aerogels are complex, arduous and costly, requiring multiple washing and soaking steps for the infiltration of the polymer precursors after gelation and supercritical drying. Additionally, diffusion problems can result in heterogeneity in aerogel monoliths due to the use of various cross-linked polymers and the autoclave-limited dimensions of aerogels. In this study, a facile sol–gel route was developed to fabricate a large (500 cm3) polymer–silica aerogel monolith that was stable under atmospheric conditions and suitable for machining. The synthesis of the polymer–silica aerogels began with a facile one-pot reaction involving resorcinol (R), formaldehyde (F), methyltrimethoxysilane (MTMS), and N-(β-aminoethyl)-γ-aminopropyl-trimethoxysilane (AEAPTES), followed by an ambient-pressure drying process. The resulting aerogels were characterised by nitrogen adsorption–desorption, scanning electron microscopy (SEM), contact angle, and thermal conductivity measurements, and the aerogel mechanical properties were evaluated by a unidirectional compression test. The Young's modulus of compression of the aerogels was observed to increase from 3.95 to 34.88 MPa with an increase in the density of the aerogels from 0.14 to 0.26 g cm−3. Simultaneously, the aerogels were observed to be superhydrophobic, with a contact angle as high as 168°, and exhibited low thermal conductivity (0.038 W m−1 K−1) and good absorption for organic liquids, which are critical characteristics for the practical application of aerogels, especially in energy-saving and oil-/chemical-cleanup practices.

STUDY ON THE PREPARATION TECHNIQUE OF SiO2 AEROGELS/FIBER COMPOSITES

Preparation and Heat Treatment of Titania Aerogels by Ambient Pressure Drying

Preparation of Methyltrimethoxysilane Derived Silica Aerogel Films via Ambient Pressure Drying

Preparation and Thermo-Mechanical Properties of Modified Gelatin Reinforced SiO2 Aerogels

Investigation of the Tetraethoxysilane‐derived Sol–gel Process by Rheological Oscillation Test and the Effect of Different Synthetic Parameters

Effects of Surfactants on the Synthesis of Silica Aerogels Prepared by Ambient Pressure Drying

Influence of Hydrolysis Time on Properties of SiO2 Aerogels Prepared by Ambient Pressure Drying

Preparation and Characterization of Hydrophobic Mesoporous SiO2 Aerogel

Study on Silica Aerogel Modified by Trimethylchlorosilane

Preparation and Characterization of Polymer Modified Silica Aerogels Dried under Ambient Pressure

Preparation and characterization of ZnO-B2O3-SO2 by sol-gel method

Synthesis and characterization of SiO2-Al2O3 composite aerogel using inorganic aluminum salt as raw material

Preparation of silica aerogel from rice hull ash by drying at atmospheric pressure

Synthesis and characterization of silica aerogels by a novel fast ambient pressure drying process

Preparation of High-Temperature Resistant Aerogels by Incorporating Aluminum Sol into Composite Silica Sources Using Ambient Pressure Drying

Preparation, mechanical, acoustic and thermal properties of silica composite aerogel using wet-laid glass fiber felt as scaffold

Preparation of Silica Aerogels Via Ambient Pressure Drying

A Facile Strategy for Freeze-Drying Preparation of Silica Aerogel from Sodium Silicate

Ambient-pressure drying synthesis of large resorcinol–formaldehyde-reinforced silica aerogels with enhanced mechanical strength and superhydrophobicity

In-situ acid catalysis strategy to achieve rapid ambient pressure drying preparation of aerogels

Synthesis of Hydrophobic Silica Aerogels via Ambient Pressure Drying