Abstract:Crack-free mesoporous equimolar Al2O3-SiO2-TiO2 ternary nanocomposite aerogel has been synthesized using an ethanol supercritical drying technique. The effects of heat treatment temperatures on its textural and structural evolution during thermal treatment are investigated in this study. XRD results reveal that only anatase phase is detected in the as-dried ternary aerogel, whereas peaks corresponding to silica and alumina phase are not shown due to its much faster polymerization rate of titania precursor. Structural transition from boehmite to γ-Al2O3 begins to occur at 450°C within the ternary aerogel, and this process is completed at nearly 615°C. The needle-like reticulated γ-Al2O3 grows along the anatase backbone, however, it is not evident in the XRD patterns. The morphologies of the ternary aerogel become more homogeneous after the structural transition, as indicated by the SEM analysis, which is also consistent with the BET results. With the increase of heat temperature up to 1050°C, the γ-Al2O3 phase disappears and no separate SiO2 is detected. At the same time, the silica-alumina network originates in a structure of Al-O-Si, and the silicon atoms incorporate into the alumina phase in the γ-Al2O3 structure, disordering the alumina primary particles. When the heat treatment temperature increases to 1200°C, mullitization begins to occur along the titania backbone, whereas silica crystallization happens at 1300°C. The 600°C calcinated ternary aerogel is typically mesoporous, showing high specific surface area (255.37m2/g), suitable average pore diameter (22.83nm) and large pore volume (1.34cm3/g). Moreover, the ternary aerogels show high surface acid activity at temperatures below 1000°C, which have future applications for ideal catalysts and catalyst supports at elevated temperatures.

Preparation and Heat Treatment of Titania Aerogels by Ambient Pressure Drying

Preparation of Methyltrimethoxysilane Derived Silica Aerogel Films via Ambient Pressure Drying

Preparation of Alumina Aerogel via Supercritical Method

Preparation of monolithic titania aerogels with high surface area by a sol–gel process combined surface modification

Effects of Surfactants on the Synthesis of Silica Aerogels Prepared by Ambient Pressure Drying

Preparation of Silica Aerogels Via Ambient Pressure Drying

Investigation on textural and structural evolution of the novel crack-free equimolar Al2O3-SiO2-TiO2 ternary aerogel during thermal treatment

Synthesis of Hydrophobic Silica Aerogels via Ambient Pressure Drying

Preparation and Characterization of Hydrophobic Silica Aerogel by Ambient Pressure Drying Method

Synthesis of Alumina Aerogels by Ambient Drying Method and Control of Their Structures

Influence of Hydrolysis Time on Properties of SiO2 Aerogels Prepared by Ambient Pressure Drying

Preparation and Characterization of Polymer Modified Silica Aerogels Dried under Ambient Pressure

Effects of Heat-Treatment Temperature on Preparation of the Sol-Gel-Derived Ag/TiO2 Films

Preparation of silica aerogel from rice hull ash by drying at atmospheric pressure

Synthesis and characterization of silica aerogels by a novel fast ambient pressure drying process

Improvement of the Thermal Insulation Performance of Silica Aerogel by Proper Heat Treatment: Microporous Structures Changes and Pyrolysis Mechanism

Preparation and Characterization of Hydrophobic Mesoporous SiO2 Aerogel

Effect of Titanium Dioxide Particles on the Thermal Stability of Silica Aerogels

Preparation of High-Temperature Resistant Aerogels by Incorporating Aluminum Sol into Composite Silica Sources Using Ambient Pressure Drying

Low thermalconductive, transparent and hydrophobic ambient pressure dried silica aerogels with various preparation conditions using sodium silicate solutions

Preparation of Monolithic Tio2 Aerogel Via Ambient Drying and Photocatalytic Degradation of Oily Wastewater