Abstract:The paper presents the influence of the temperature of the sintering process on the microstructure and selected properties of boron carbide/TiB2/SiC composites obtained in situ by spark plasma sintering (SPS). The homogeneous mixture of boron carbide and 5% vol. Ti5Si3 micropowders were used as the initial material. Spark plasma sintering was conducted at 1700 °C, 1800 °C, and 1900 °C for 10 min after the initial pressing at 35 MPa. The heating and cooling rate was 200 °C/min. The obtained boron carbide composites were subjected to density measurement, an analysis of the chemical and phase composition, microstructure examination, and dry friction-wear tests in ball-on-disc geometry using WC as a counterpart material. The phase compositions of the produced composites differed from the composition of the initial powder mixture. Instead of titanium silicide, two new phases appeared: TiB2 and SiC. The complete disappearance of Ti5Si3 was accompanied by a decrease in the boron carbide content of the stoichiometry formula B13C2 and an increase in the content of TiB2, while the SiC content was almost constant. The relative density of the obtained boron carbide composites, as well as their hardness and resistance to wear, increased with the sintering temperature and TiB2 content. Unfortunately, the reactions occurring during sintering did not allow us to obtain composites with high density and hardness. The relative density was 76–85.2% of the theoretical one, while the Vickers hardness was in the range of 4–12 GPa. The mechanism wear of boron carbide composites tested in friction contact with WC was abrasive. The volumetric wear rate (Wv) of composites decreased with increasing sintering temperature and TiB2 content. The average value of coefficient of friction (CoF) was in the range of 0.54–0.61, i.e., it did not differ significantly from the value for B4C sinters.

Densification and grain growth kinetics of boron carbide powder during ultrahigh temperature spark plasma sintering

Continuum Modeling of B4C Densification During Spark Plasma Sintering

Multi-stage spark plasma sintering to study the densification mechanisms of boron carbide

Preparation of dense B4C ceramics by spark plasma sintering of high-purity nanoparticles

Densification and strengthening mechanism in spark plasma sintering of B4C–VB2 ceramics via carbide boronizing

Influence of Length-Scale on Stabilization of Boron Carbide in Al-based Metal Matrix Composites During Plasma Activated Sintering

Densification and microstructure evolution of W-TiC-Y2O3 during spark plasma sintering

Densification mechanism, microstructure and mechanical properties of ZrC ceramics prepared by high-pressure spark plasma sintering

Novel approach of the evaluation of electric current density during the spark plasma sintering: Effect on the densification mechanisms of B4C-based ceramics

Microstructure and mechanical properties of spark plasma sintered SiC ceramics aided by B4C

Densification, microstructure and properties of ultra-high temperature HfB2 ceramics by the spark plasma sintering without any additives

Influence of CNTs on the Sintering Behavior and Mechanical Properties of Boron Carbide by SPS Process

Influence of Silicon Addition on the Sintering Behavior and Mechanical Properties of Boron Carbide by SPS Process

Carbon contamination of elemental beta-boron promoted a stable boron carbide by spark plasma sintering

Densification and mechanical properties of boron carbide prepared via spark plasma sintering with cubic boron nitride as an additive

Sintering mechanism of pure B4C ceramic prepared by hot oscillating pressing and with excellent mechanical properties

Numerical Simulation of Physical Fields during Spark Plasma Sintering of Boron Carbide

Processing and mechanical properties of B4C-SiCw ceramics densified by spark plasma sintering

Densification and Mechanical Properties of Tic by Sps-Effects of Holding Time, Sintering Temperature and Pressure Condition

The Microstructure, Mechanical, and Friction-Wear Properties of Boron Carbide-Based Composites with TiB2 and SiC Formed In Situ by Reactive Spark Plasma Sintering

Spark plasma sintering and hot pressing of ZrB2–SiCW ultra-high temperature ceramics