Abstract:Due to the high modulus, high strength, low density, excellent wear resistance and good neutron absorption, the boron carbide (B4C) particle reinforced aluminum (Al) matrix composites have been widely applied in the aerospace, weaponry, transportation and neutron shielding fields. In response to the increasing requirement of better strength -ductility matching of B4C/Al composites, introducing a nano-scale reinforcement into the B4C/Al composites becomes an attractive research focus. In this work, the SiC nanowires were ball-milled with Al powders, and then the SiC/Al composite powders were mixed with B4C microparticles. Thus, the 15vol. % B4C/SiC/Al composites with different volume fractions of SiC nanowires were fabricated by hot-pressing sintering and hot extrusion. B4C microparticles and SiC nanowires are uniformly dispersed in the B4C/SiC/Al composites, while the introduced SiC nanowires effectively decrease the Al matrix grain sizes. B4C/SiC/Al composites produce the better strength-ductility matching than that of B4C/Al composites, while the 15vol. % B4C/SiC/Al composite with 1vol. % SiC nanowires achieved the best strength-ductility matching. It generates the 281.7 ± 2.7 MPa in yield strength, 351.2 ± 0.1 MPa in ultimate tensile strength and 5.9 ± 0.7% in failure elongation, which are increased by 18.2%, 15.1% and 13.5% compared to the B4C/Al composites. Uniformly dispersed B4C microparticles and SiC nanowires largely block the dislocation motions and improve the dislocation storage capacity, which results in a more significant hetero-deformation induced (HDI) hardening effect in the B4C/SiC/Al composites. Moreover, the B4C/Al interfacial transition regions with the added SiC nanowires becomes stronger, which can enhance the load transfer efficiency of the B4C/Al interfaces as a result of the existing dislocation hardening zones. In conclusion, it is a good strategy to combine the synergistic strengthening effect of micro-scale and nano-scale reinforcements in the metal matrix composites.

Influence of Length-Scale on Stabilization of Boron Carbide in Al-based Metal Matrix Composites During Plasma Activated Sintering

Influence of particulate B4C with high weight fraction on microstructure and mechanical behavior of an Al-based metal matrix composite

Fabrication, microstructure characterization and mechanical properties of B4C microparticles and SiC nanowires hybrid reinforced aluminum matrix composites

Towards Homogeneous Distribution of Coarse Grain in a Tri-Modal Al-based Composites Utilizing Localized Grain Growth

Continuum Modeling of B4C Densification During Spark Plasma Sintering

Influence of Sintering Process Conditions on Microstructural and Mechanical Properties of Boron Carbide Ceramics Synthesized by Spark Plasma Sintering

Densification and strengthening mechanism in spark plasma sintering of B4C–VB2 ceramics via carbide boronizing

Effect of B4C Particle Size on the Mechanical Properties of B4C Reinforced Aluminum Matrix Layered Composite

Effect of High Volume Fraction of B4C Particles on the Microstructure and Mechanical Properties of Aluminum Alloy Based Composites

Microstructure Evolution of 15wt% Boron Carbide/Aluminum Composites During Liquid-Stirring Process

Densification and mechanical properties of boron carbide prepared via spark plasma sintering with cubic boron nitride as an additive

Effect of particle size and volume fraction on the strengthening mechanisms of boron carbide reinforced aluminum metal matrix composites

Effect of Si/C Ratio and Their Content on the Microstructure and Properties of Si–B–C–N Ceramics Prepared by Spark Plasma Sintering Techniques

Regulating the Mechanical Properties of (μm B4C+nm SiC)/7075Al Composites Via Nano-Sic Content

Microstructure, Mechanical Properties, and Corrosion Behavior of Boron Carbide Reinforced Aluminum Alloy (Al-Fe-Si-Zn-Cu) Matrix Composites Produced via Powder Metallurgy Route

Influence of particulate B4C size on microstructural evolution and mechanical behavior in nanostructured Al matrix during heat treatment

Effect of B4C on Microstructure Evolution and High-Temperature Mechanical Properties of TiAl Matrix Composites

Influence of CNTs on the Sintering Behavior and Mechanical Properties of Boron Carbide by SPS Process

Preparation of dense B4C ceramics by spark plasma sintering of high-purity nanoparticles

Thermally Stable Microstructures and Mechanical Properties of B 4 C-Al Composite with In-Situ Formed Mg（Al）B 2

Effect of alumina addition on the densification of boron carbide ceramics prepared by spark plasma sintering technique