Abstract:Due to native deficiency of the interfacial mismatch between Al2O3 and Al-melt, as well as micron-Al2O3 segregation at matrix grain boundaries (GBs), achieving both high strength and fracture toughness has been the long-lasting challenge for Al-CuO composite fabricated by conventional casting. Herein, we report a novel manufacturing of Al-CuO composite via shift-speed ball-milling (SSBM) of Al-5 wt.% CuO powders and afterwards subjected to hot-pressing (HP) as well as heat treatment. Comprehensive characterization shows that in-situ generation of the two types of Al2O3 with intragranular distribution, including δ*-Al2O3 particles (∼200 nm) and γ-Al2O3 whiskers (length of ∼150 nm, thickness of ∼20 nm), was governed by a diffusion-assisted nucleation-regime ascribing to the intense thermal effect of Al-CuO reaction. The size and spatial distribution of Al2O3 were emphasized to address their contribution to the high mechanical performance of the composite, which exhibits a tensile strength of ∼481 MPa and fracture elongation of ∼16.8 %. Meanwhile, the toughening mechanism of present Al-CuO composite was rationalized on basis of the "dislocation punched zone" and "plastic zone" affected by Al2O3. Both the theoretical analysis and fracture morphology support a reinforcements-matrix interface failure mechanism and the non-uniform distribution of Al2O3 consisting alternant "rich/poor zones" can markedly contribute to the high toughness. The present findings may provide a promising strategy to achieve an intragranular distribution of nano-sized reinforcements in Al-metal oxides composites, which enables increasing strength and ductility of the metal matrix.

Towards Homogeneous Distribution of Coarse Grain in a Tri-Modal Al-based Composites Utilizing Localized Grain Growth

MMCs with Controlled Non-Uniform Distribution of Submicrometre Al2O3particles in 6061 Aluminium Alloy Matrix

Influence of coarse grain particles on mechanical properties and fracture behavior in multi-modal Al-based metal matrix composites

Interfacial Segregation and Precipitates Behavior in the Ultrafine Grained Al-based Metal Matrix Composites

Enhanced strain hardening by bimodal grain structure in carbon nanotube reinforced Al–Mg composites

Enhanced Combination of Strength and Ductility in Ultrafine-Grained Aluminum Composites Reinforced with High Content Intragranular Nanoparticles

Influence of particulate B4C with high weight fraction on microstructure and mechanical behavior of an Al-based metal matrix composite

Influence of Length-Scale on Stabilization of Boron Carbide in Al-based Metal Matrix Composites During Plasma Activated Sintering

Microstructures and Mechanical Properties of a L12-structured Precipitation Strengthened Co-based Superalloy

Balanced strength and ductility in B 4 C/SiC/2024Al composite with multimodal grain structure achieved by multistep ball milling and powder metallurgy

A tri-modal aluminum based composite with super-high strength

Grain growth and strengthening mechanisms of ultrafine-grained CoCrFeNiMn high entropy alloy matrix nanocomposites fabricated by powder metallurgy

Revealing the strengthening and toughening mechanisms of Al-CuO composite fabricated via in-situ solid-state reaction

Bimodal-grain structure enables superior strength-ductility synergy of pure Al

Synthesis and characterization of an in-situ Al2O3/Al–Cu composite with a heterogeneous structure

Tailoring of nanoscale γ' precipitates and unveiling their strengthening mechanisms in multimodal nickel-based superalloy GH4720Li

Microstructure evolution and mechanical properties of CoCrFeNiAl0.3 high entropy alloy produced by ball milling in combination with thermomechanical consolidation

Improving the Tensile Ductility and Uniform Elongation of High-Strength Ultrafine-Grained Al Alloys by Lowering the Grain Boundary Misorientation Angle

Development of bimodal grain-structured Al-Zn-Mg-Cu-Zr alloys for strength-ductility synergy via microalloying with Hf and Sc

Preparation of heterogeneous nanolaminated graphene nanosheet/Al–Cu–Mg composites by powder assembly & alloying

Microstructures and mechanical properties of Al nanocomposites hybrid-reinforced with B4C, carbon nanotubes and graphene nanoplatelets