Abstract:Designing a novel microstructure with higher strength-ductility than lamellar microstructure (LM), which has been considered the most valuable engineering application in the service temperature range, is desired for lightweight TiAl alloys. Our prior publication reported a three-phase tri-modal (T-T) structure for Ti-43.5Al-4Nb-1Mo-0.1B(.at%) with superior mechanical properties than LM at room temperature (Ref: Acta Mater. 225 (2022) 117585). However, its strength-ductility at working temperature has yet to be fully exploited. This work fills the much-needed gap. The qualitative and quantitative optimizations indicate that the T-T structure's yield strength increases first and then decreases with increasing pearlitic-like microstructure (PM, which consist of three-phase (α 2 , γ and β o phase) with clear orientation relationships that form in a lamellar/cellular manner) content while the ductility keeps rising. When the T-T structure contains ∼20% PMs, it exhibits a yield strength about 130 MPa higher than LM coupling with doubled ductility at 750 °C. PMs can induce a prominent twinning induced plasticity and dislocation jog dragging (TWIP&DJD) effect, resulting in better strength-ductility below 700°C; above this temperature, the TWIP&DJD effect significantly plasticizes the alloys. The higher strength of the T-T structure at 750 °C is caused by hetero-deformation-induced strengthening between LMs and PMs, which cannot be offset by the plasticizing caused by PM when the volume fraction of PMs is less than 50%. This study demonstrates that introducing an appropriate amount of plasticizing structures (similar to PM) with excellent work hardening capacity is a promising strategy for enhancing the strength-ductility synergy of TiAl and possibly other brittle materials.

Improving the Tensile Ductility and Uniform Elongation of High-Strength Ultrafine-Grained Al Alloys by Lowering the Grain Boundary Misorientation Angle

Enhancing Ductility of Titanium Matrix Composites by Multimodal Α-Grains

Optimizing the strength and ductility of fine structured 2024 Al alloy by nano-precipitation

Deformation and Fracture Mechanisms of an Annealing-Tailored "bimodal" Grain-Structured Mg Alloy

Grain-anisotropied High-Strength Ni6Cr4WFe9Ti High Entropy Alloys with Outstanding Tensile Ductility

Tailoring bimodal grain structure of Mg-9Al-1Zn alloy for strength-ductility synergy: Co-regulating effect from coarse Al2Y and submicron Mg17Al12 particles

Bimodal-grain structure enables superior strength-ductility synergy of pure Al

Effect of Abnormal Grain Refinement on Synchronous Strengthening Behavior of Fe50Mn30Co10Cr10 High Entropy Alloys

Achieving Superior Strength-Ductility Balance by Tailoring Dislocation Density and Shearable GP Zone of Extruded Al-Cu-Li Alloy

Enhanced ductility in coarse grained Fe3Al alloys

Tuning the Microstructure and Mechanical Properties of TiAl-based Alloy Through Grain Boundary Engineering

Enhancing Strength-Ductility Synergy in an Extruded Al-Cu-Li-Mg-Ag Alloy Via Homogeneous GP Zones and Dislocation Configuration

Hierarchical Grain Size and Nanotwin Gradient Microstructure for Improved Mechanical Properties of a Non-Equiatomic CoCrFeMnNi High-Entropy Alloy

Breaking the high-temperature strength-ductility trade-off in TiAl alloys through microstructural optimization

Enhancing Strength-Ductility Synergy Via Hierarchical Microstructure in Fine-Grained Ti-10Mo-8V-1Fe-3.5Al Alloy

Achieving ultrahigh strength in binary Al-10Mg alloy through heavy cryogenic rolling

Improvement on high-temperature tensile strength and ductility of selective electron beam melting TiAl alloys via small-strain forging

Deformation-Induced Grain Refinement and Amorphization in Ti-10V-2Fe-3Al Alloy

Designing Ultrastrong and Thermally Stable FeCrAl Alloys with the Fine-Grained Structure

New insights into ductility improvement of a nickel-based superalloy through grain boundary engineering

Microstructural and mechanical behavior of Al-Mg-Mn-Sc-Zr alloy subjected to multi-axial forging at room temperature