Abstract:Tungsten carbide (WC), celebrated for its exceptional strength, hardness, and chemical inertness, serves as an exemplary reinforcement for copper (Cu) matrix composite (CMC) coatings, significantly enhancing their wear and corrosion resistance. However, the inherent poor wettability and interfacial bonding between WC and Cu during the cold spray additive manufacturing process pose challenges to further performance improvement of these coatings. This study investigates cold-sprayed CMC coatings reinforced with WC particles, both with and without an electroless plated cobalt (Co) shell (Co@WC; at 10 wt.% and 20 wt.%), focusing on their microstructure, mechanical properties, tribological behavior, and electrochemical corrosion resistance. The findings indicate a reduction in CMC coatings` porosity and mean free path (MFP) of reinforcement particles with increasing reinforcement content. Despite slight Co shell damage during deposition, ceramic retention is notably enhanced, reaching up to 149.3%. The microhardness and wear resistance of CMC coating are improved with decreased MFP and increased ceramic content. Compared to the Cu coating, the microhardness of CMC coatings escalates by up to 32.9% (151.8HV0.1), and the specific wear rate is dramatically reduced by up to 84.2%. The Co shell effectively prevents the detachment of Co@WC particles, thereby enhancing the bending and wear resistance. Electrochemical corrosion tests, encompassing open circuit potential (EOCP), polarization curve, and electrochemical impedance spectroscopy (EIS), indicate that lower porosity, high ceramic content and the Co shell substantially boost the corrosion resistance of the CMC coating. Specifically, the coating with 20 wt.% Co@WC (Cu20(Co@WC)) demonstrates superior corrosion resistance compared to the Cu coating, hinting at the potential for further enhancement with increased ceramic content.

Characterization of Thick Tungsten Coating on Cu Alloy Substrate Prepared by Electrodeposition

Thermal Shock Performance of CVD Tungsten Coating at Elevated Temperatures

Surface morphology and crystal orientation of electrodeposited tungsten coatings with different pulse parameters

Characteristics of Tungsten Coatings Deposited by Molten Salt Electro-Deposition and Thermal Fatigue Properties of Electrodeposited Tungsten Coatings

Cold-sprayed Cu Matrix Composite Coatings with Core-Shell Structured Co@WC Reinforcements on Q235 Steel

Robust Ni/WC superhydrophobic surfaces by electrodeposition

Preparation, characterisation and electrochemical study of crack-free nanocrystalline electrodeposited Co-W alloy coating of high hardness

Preparation and Properties of Textured Ni–W Coatings Electrodeposited on the Steel Surface from a Pyrophosphate Bath

The W alloying effect on thermal stability and hardening of nanostructured Cu-W alloyed thin films

Microstructure and wear properties of crystalline W alloy coatings prepared by electrodeposition

Study of Thick Tungsten Coatings Deposited on Various Molybdenum and Copper Substrates

Preparation of Cu-ZrW2O8 Composite Coatings by Electric Deposition

Substrate dilution and interface structures of tungsten coating deposited by double-glow plasma surface alloying on stainless steel substrate

Evolution of surface morphology, roughness and texture of tungsten disilicide coatings on tungsten substrate

Depth profiling of tungsten coating layer on CuCrZr alloy using LIBS approach

Coating process conditions of W alloy electrodeposition

Electrodeposition of High-Quality Cr Coatings with Solid Solution Al from Cr2+ Electrolyte

Characteristics of tungsten coating on silicon particles prepared by sol-gel method

Characterization of Cr Coating Obtained on Micrometer-Scale Diamond Particles Prepared by Molten Salt Method

Influences of Co and process parameters on structure and corrosion properties of nanocrystalline Ni-W-Co ternary alloy film fabricated by electrodeposition at low current density

Thermal Performance and Microstructure of Vacuum Plasma Sprayed Tungsten Coatings under Cyclic Heat Load