Abstract:Tungsten carbide (WC), celebrated for its exceptional strength, hardness, and chemical inertness, serves as an exemplary reinforcement for copper (Cu) matrix composite (CMC) coatings, significantly enhancing their wear and corrosion resistance. However, the inherent poor wettability and interfacial bonding between WC and Cu during the cold spray additive manufacturing process pose challenges to further performance improvement of these coatings. This study investigates cold-sprayed CMC coatings reinforced with WC particles, both with and without an electroless plated cobalt (Co) shell (Co@WC; at 10 wt.% and 20 wt.%), focusing on their microstructure, mechanical properties, tribological behavior, and electrochemical corrosion resistance. The findings indicate a reduction in CMC coatings` porosity and mean free path (MFP) of reinforcement particles with increasing reinforcement content. Despite slight Co shell damage during deposition, ceramic retention is notably enhanced, reaching up to 149.3%. The microhardness and wear resistance of CMC coating are improved with decreased MFP and increased ceramic content. Compared to the Cu coating, the microhardness of CMC coatings escalates by up to 32.9% (151.8HV0.1), and the specific wear rate is dramatically reduced by up to 84.2%. The Co shell effectively prevents the detachment of Co@WC particles, thereby enhancing the bending and wear resistance. Electrochemical corrosion tests, encompassing open circuit potential (EOCP), polarization curve, and electrochemical impedance spectroscopy (EIS), indicate that lower porosity, high ceramic content and the Co shell substantially boost the corrosion resistance of the CMC coating. Specifically, the coating with 20 wt.% Co@WC (Cu20(Co@WC)) demonstrates superior corrosion resistance compared to the Cu coating, hinting at the potential for further enhancement with increased ceramic content.

Preparation of Cu-ZrW2O8 Composite Coatings by Electric Deposition

Preparation of Cu Coated ZrW<sub>2</sub>O<sub>8</sub> Composite Powders Via Heterogeneous Precipitation Process

Thermal properties and phase transitions of Cu-coated ZrW 2O 8 composite powders

Thermal properties and phase transitions of Cu-coated ZrW<sub>2</sub>O<sub>8</sub> composite powders

Microstructure and Ablation Behavior of W Coating Prepared by Atmospheric Plasma Spraying for Zr/Cu Infiltrated C/C Composites

Preparation of WC/Co Powders by Electroless Plating and Its Coating on 2cr13 Stainless Steel by Laser Cladding

PREPARATION OF ULTRAFINE W–Cu COMPOSITE POWDER USING ULTRASONIC-ASSISTED ELECTROLESS PLATING

Cold-sprayed Cu Matrix Composite Coatings with Core-Shell Structured Co@WC Reinforcements on Q235 Steel

Fabrication and Characterization of Ni–Zr Composite Coatings Using Electrodepositing Technique

Electrodeposition of Ni-WC composite coatings: formation, structure and properties

Electrodeposition of Ni Matrix Composite Coatings Containing Zrc Particles

Enhanced mechanical properties and corrosion resistance of electro-deposited NiCoP composite coatings with ZrB2 particle addition

Effect of Zr Target Current on the Mechanical and Tribological Performance of MoS2–Zr Composite Lubricating Coatings

Fabrication of Pb-Co-ZrO 2 nanocomposite coatings and correlation of corrosion mechanisms with electronic work functions

Ultrasound Supported Galvanostatic Deposition of Zn Coatings Reinforced with Nano-, Submicro-, and Micro-SiC Particles—Weak Acidic Chloride Baths

Characterization of Thick Tungsten Coating on Cu Alloy Substrate Prepared by Electrodeposition

Investigation on Microstructure and Tribological Performances of Electrodeposited Ni-W-Y2O3 Composite Coatings

The microstructure and wear resistance characteristics of electroformed nickel and partially stabilized zirconia composite coatings

Preparation and Corrosion Resistance of Ni-W-CF Composite Coating on P110 Steel

Hydrothermal Synthesis of ZrW2O8 Nanorods and Its Application in ZrW2O8/Cu Composites with Controllable Thermal Expansion Coefficients

The Oxidation Performance for Zr-doped Nickel Aluminide Coating by Composite Electrodepositing and Pack Cementation