Abstract:This study successfully prepared crack-free WC10%-Ni60AA cermet coatings with high hardness using directed-energy deposition incorporating substrate preheating up to 500 °C. At the bottom of the deposit, the crack-free coating microstructure exhibited a lamination layer with a coarse herringbone eutectic, and the crystal-microstructure phase mainly comprised γ-Ni solid solution and eutectic precipitation Ni 17 W 3 , Ni 31 Si 12 , and Cr 23 C 6 . At the middle and top of the deposit, the microstructure exhibited a dense net-like eutectic, including a dendritic with the main phase of γ-Ni solid solution, interdendritic with a main phase of Cr 23 C 6 , and subdendritic with a main phase of Ni 31 Si 12 , Ni 17 W 3 , and a small block-like precipitate with a main phase of Cr 2.4 W 0.6 Si. Furthermore, the deposits on the substrate preheated to 500 °C exhibited the highest hardness (812 HV, an increase of 64 % compared to that of the non-preheating sample) owing to the dense net-like eutectic precipitation with fine-grain structure. Furthermore, wear test results show that the wearing process is divided into three stages: the rapid-increase stage; the plowing-friction stage; and the stable-wear stage. Specifically, as the load increased from 100 N to 400 N, the width and depth of the wear tracks increased, and the wear mechanisms were adhesive and oxidation, with the most severe wear occurring under a load of 400 N. Similarly, as the speed increased from 50 RPM to 300 RPM, the width and depth of the wear tracks increased, and the wear mechanisms were adhesive and oxidation at low speeds. When the speed was increased to 300 RPM, the most severe wear occurred, and the wear mechanisms were primarily adhesive and abrasive, along with a small amount of oxidation wear.

Microstructure and wear properties of crystalline W alloy coatings prepared by electrodeposition

Wear and Corrosion Properties of Crystalline Ni-W Alloy Coatings Prepared by Electrodeposition

Effect of Process Parameters on Microstructure and Properties of AlCoCrFeNi-WC-WS2 Composite Coating Prepared by Laser Cladding

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

Preparation and Properties of Textured Ni–W Coatings Electrodeposited on the Steel Surface from a Pyrophosphate Bath

Coating process conditions of W alloy electrodeposition

Mechanical and Tribological Properties of Ni-B and Ni-B-W Coatings Prepared by Electroless Plating

Microstructure and Wear Behavior of Hard Ni60 and Soft WC-12Co/Ni25 Coatings Prepared by Laser Cladding on W1813N Non-magnetic Stainless Steel

Microstructure and Wear Behavior of Hard Ni60 and Soft WC-12Co/N125 Coatings Prepared by Laser Cladding on W1813N Non-magnetic Stainless Steel

Excellent Properties of Ni-15 wt.% W Alloy Electrodeposited from a Low-Temperature Pyrophosphate System

Microstructure and wear behaviors of a WC10%-Ni60AA cermet coating synthesized by laser-directed energy deposition

Effects of W Alloying on the Lattice Distortion and Wear Behavior of Laser Cladding AlCoCrFeNiWx High-Entropy Alloy Coatings

Hardness and tribological properties of co-electrodeposited Ni-W-B/B coatings

Mechanical properties of Ni-based coatings fabricated by electroless plating method

Preparation, Mechanical Properties and Wear Resistance of Ni–W/SiC Nanocomposite Coatings

Investigations on the Influence of Annealing on Microstructure and Mechanical Properties of Electrodeposited Ni-Mo and Ni-Mo-W Alloy Coatings

Repair of tungsten heavy alloy die casting molds with laser cladded CoCrFeNiWx high entropy alloy Coatings: Microstructure, wear properties and tempering stability

Research on microstructure, mechanical property and wear mechanism of AlCoCrFeNi/WC composite coating fabricated by HVOF

Microstructure and wear behavior of WC-reinforced AlCoCrFeNiSi high entropy alloy coatings prepared by high-velocity arc spraying

Tribological Performance and Wear Mechanism of Laser Cladded NiCrAl-WC Coatings at High-Temperature

The alloying effects of Cr on in-situ phase evolution and wear resistance of nickel composite coatings fabricated by wide-band laser deposition