Abstract:The use of metal-coated ceramic powders not only effectively enhances the wettability of the metal–ceramic interface but also promotes a more uniform microstructure in Ti(C,N)-based cermets, which is advantageous for improving their mechanical properties. In this study, ultrafine Co- and Ni-coated (Ti,W,Mo,Ta)(C,N) powders were synthesized via the spray-drying-in-situ carbothermal reduction method. Subsequently, Ti(C,N)-based cermets were effectively fabricated using the as-prepared ultrafine Co- and Ni-coated (Ti,W,Mo,Ta)(C,N) powders. The impact of reaction temperature, heating rate, and isothermal time on the phase and microstructure of prepared powders was analyzed using X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). Additionally, the microstructure of the as-sintered cermets was experimentally investigated. The findings reveal that the complete reduction of Co and Ni metal salts, pre-coated on the surface of (Ti,W,Mo,Ta)(C,N) particles, can be achieved through rapid heating (10 °C/min) in a specific temperature range (600–1000 °C) with an isothermal time of 3 h at a lower reduction temperature (1000 °C). The synthesized powders have only two phases: the (Ti,W,Mo,Ta)(C,N) phase and Co/Ni phase, and no other heterogeneous phases were observed with an oxygen content of 0.261 wt.%. Notably, the conventional core–rim structure was not dominant in the cermets obtained from the prepared Co- and Ni-coated (Ti,W,Mo,Ta)(C,N) powders. Moreover, the heterogeneous segregation effect of the Co/Ni coating on the ultrafine powder particles resulted in a finer microstructure than the traditional cermets with the same composition. However, the grain size is mainly in the range of 0.5–0.8 μm. The weaker residual stresses at the core and rim interfaces and the finer particle distributions could theoretically enhance the toughness of Ti(C,N)-based cermets, simultaneously.

Synthesis of nano (Ti,W)C powder with preferred orientation and twin boundary structure

A Tungsten-Based Nanolaminated Ternary Carbide: (W,Ti)4C4- x

Synthesis and Formation Mechanism of W/TiC Composite Powders by a Wet Chemical Route

Preparation of Ultrafine Co- and Ni-Coated (Ti,W,Mo,Ta)(C,N) Powders and Their Influence on the Microstructure of Ti(C,N)-Based Cermets

Preparation and Characteristics of W–1 Wt.% TiC Alloy Via a Novel Chemical Method and Spark Plasma Sintering

Synthesis and Field Emission Properties of Titanium Carbide Nanowires

Strengthening and toughening of Ti(C,N)-based cermets: (Ti,W)C additive design and the mechanism

In-situ Synthesis of Nanocrystalline TiC Powders, Nanorods, and Nanosheets in Molten Salt by Disproportionation Reaction of Ti(II) Species

Preparation and Sinterability of Submicron Titanium Carbide Powders Synthesized with Phenolic Resin As Carbon Source by Carbothermal Reduction

Fabrication of Ultra-Fine-Grained W-TiC Alloys by a Simple Ball-Milling and Hydrogen Reduction Method

The influence of Ti-induced precipitates on the microstructure and mechanical properties of (Zr,W)C solid solution

Preparation of high-entropy (Ti,Nb,Ta,Mo,W)(C,N) ceramics via carbothermal reduction nitridation using different carbon source

Ultra-High Hardness TiC-W-Ni Cermets Prepared by Spark Plasma Sintering of Ultra-Fine TiC Powder

Preparation of TiC/W Core–shell Structured Powders by One-Step Activation and Chemical Reduction Process

High entropy six-component solid solution (Ti0.5Nb0.15Zr0.1Mo0.1Ta0.1W0.05)2AlC: A novel synthesis approach and its mechanical properties

Tunable mechanical properties and excellent microwave transparent performance of full spectrum (Ti Ta1-)C microcuboids (0 < x < 1) synthesized via a dissolution-precipitation strategy

Effect of Ni content on the microstructure and properties of WCoB-TiC cermets

Direct Synthesis of Controllable Microstructures of Thermally Stable and Ordered Mesoporous Crystalline Titanium Oxides and Carbide/Carbon Composites

One-step Preparation of Dense TiC1 − Xnx–ni3ti Cermet by Combustion Synthesis

Microhomogeneous WC-TiC-Co composite powders with enhanced sinterability via a two-step carburization method

The production of in situ (Mo,Ti)(C,N)-based cermets without a core/rim structure by reaction hot pressing: Formation mechanism and mechanical properties