Abstract:Transition metal boride enable applications in fields of cutting tools as the hard phase, but their fabrication suffers from shortcomings in high temperature for binary and hard/soft phase balance. Here, we leveraged a WCoB-Co cermets prepared by using elemental powders of W, Co and B powders via in situ synthesis method and investigated the microstructure evolution of a composite structure of WCoB/Co. The phase evolution, microstructure evolution and mechanical properties were investigated using X-ray diffraction (XRD), differential scanning calorimetry (DSC), scanning electron microscopy (SEM) and energy dispersive spectrometer (EDS). The complete sintering process consist of three solid-phase reaction stages and one liquid-phase sintering stage. The solid-phase reaction stage includes the following three reactions: B + 2Co → Co2B, 11 W +15 Co2B → 9WCoB + W2Co21B6, and 14 W + 2W2Co21B6 → 12WCoB + 23Co + Co7W6. The eutectic liquid phase, essential for the densification, forms at 1323 °C. The Rockwell hardness and density value reach 87.5HRA and 12.11 g/cm3, respectively. At 1380 °C, the traverse rupture strength (TRS) reaches the peak value of 1495 MPa. Moreover, the results show that transgranular fracture is the main fracture mode. The densification stage was completed at ~1400 °C. In particular, Co7W6 phase was discovered during the study of the evolution of WCoB-Co cermets. An increase of the B content was found to be beneficial to eliminate the Co7W6 phase that proved to be detrimental to mechanical properties.

Effect of Ni content on the microstructure and properties of WCoB-TiC cermets

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

Influences of Ni/Cu/Cr3C2 Composite Additive on Microstructure and Properties of WC–10Co Fine Grained Hardmetal

Effects of WC content on core/rim phases and microstructure of TiB2-TiC-WC-(Co-Ni) cermets

Correlation between microstructure and mechanical properties of Ti(C,N)-xWC-Ni cermets prepared by mechanical activation and subsequent in situ carbothermal reduction

Ultra-High Hardness TiC-W-Ni Cermets Prepared by Spark Plasma Sintering of Ultra-Fine TiC Powder

Tracking the evolution of microstructure and phases of WCoB-Co cermets during sintering

Microstructures and Properties of WC-10 wt.%CoCrFeNiAlx Composite Cemented Carbides

Effect of cobalt content on the microstructure, microtexture, and mechanical properties of W-Ni-Fe-xCo alloys during solid-phase-sintering and liquid-phase-sintering

Synthesis and Microstructure Evolution of WCoB Based Cermets During Spark Plasma Sintering

Effect of WC-Co Granules on Mechanical Properties and Microstructure of Ti(C,N)-based Cermets

Effects of CrMnFeCoNi additions on microstructure, mechanical properties and wear resistance of Ti(C,N)-based cermets

Achieving hardness‐strength‐toughness synergy in (Ti, W, Mo, Cr)(C, N)‐based cermets

Effect of Mn addition on the microstructure, interface structure and mechanical properties of MoCoB–Co cermets prepared by in-situ synthesis

Influence of Ni Content on the Structure and Mechanical Properties of Ultrafine WC-Ni-VC-TaC Hardmetals

Effect of Y2O3 Addition on the Microstructure and Mechanical Properties of TiCN-based Cermets

Enhancing the wear resistance of sintered WC–Co composite by adding pseudo-elastic TiNi constituent

Effect of Mo Addition on Microstructure, Magnetic and Mechanical Properties of TiC-TiN-WC-Ni Cermets

Effect of tungsten carbide content on the tribological behavior of TiB2–TiC-based cermets

Effects of WC/TiC addition on the thermodynamic behavior of TiB 2 -based cermet during sintering process

Effect of Ni Content on the Microstructure, Mechanical Properties and Erosive Wear of Mo2NiB2–Ni Cermets