Abstract:TiC bonded diamond composites were prepared from a mixture of Ti, graphite, and diamond powders as raw materials, with Si as sintering additives, through high-temperature and high-pressure (HTHP) technology. The reaction between Ti and graphite under 4.5–5 GPa pressure and 1.7–2.3 kW output power can produce TiC as the main phase. The diamond particles are surrounded by TiC, and the interface is firmly bonded. The coefficient of friction (COF) of TiC–diamond composites with POM and PP balls decreases with increasing load for a specific friction velocity. However, the COF of TiC–diamond composites with agate, Cu and Al balls increases with the rising load because of the enhanced adhesive wear effect. The COF of PP, Cu and Al balls slightly increases with the increase in friction velocity at a certain load. SEM results show that the surface of agate balls has rough, pear-shaped grooves and shallow scratches. The scratches on the surface of POM balls are wrinkled. The PP balls have pear-shaped groove scratches on their wear surfaces. The wear mechanism of TiC–diamond composites with Cu ball pairs is primarily adhesive wear. The abrasion of TiC–diamond composites with Cu ball pairs remains almost unchanged as the load increases. However, the depth and width of the pear-shaped grooves on the wear surface of TiC–diamond composites are significantly increased. This phenomenon may be attributed to the high rotational speed, which helps to remove the residual abrasive debris from the friction grooves. As a result, there is a decrease in both the depth and width of the pear-shaped grooves, leading to a smoother overall surface. The wear mechanism of TiC–diamond composites with Al ball pairs is abrasive wear, which increases with an increasing load. When the load is constant, as the speed increases, the wear morphology of TiC–diamond composites with Al ball pairs transitions from rough to smooth and then back to rough again. This phenomenon may be attributed to the wear mechanism at low speeds being groove wear and adhesive wear. As the speed increases, the wear particles are more easily removed from the wear track, leading to a reduction in abrasiveness. As the speed increases, the wear surface becomes roughened by a combination of grooves and dispersed wear debris. This can be attributed to the increased dynamic interaction between surfaces caused by higher speed, resulting in a combination of abrasive and adhesive wear. In addition, Cu and Al ball wear debris appeared as irregular particles that permeated and adhered to the surface of the TiC phase among the diamond particles. The results suggest that TiC–diamond composites are a very promising friction material.

Effect of tungsten carbide content on the tribological behavior of TiB2–TiC-based cermets

Effects of WC/TiC addition on the thermodynamic behavior of TiB 2 -based cermet during sintering process

Effects of WC content on core/rim phases and microstructure of TiB2-TiC-WC-(Co-Ni) cermets

Microstructure and Tribological Properties of WC/Ni-MoS2 Titanium-Based Composite Coating on TC4

Research On Wear Behavior Of Atc Cermet Material

Correlation between microstructure and mechanical properties of Ti(C,N)-xWC-Ni cermets prepared by mechanical activation and subsequent in situ carbothermal reduction

Carburization And Wear Behavior Of Self-Lubricating Ti(C,N)-Based Cermets With Various Secondary Carbides

Influence of WC content on microstructure and mechanical properties of Mo2FeB2-based cermets fabricated by multi-step sintering

Microstructural characteristics and wear-resistant mechanisms of WC-TiC-co coatings with varying TiC contents

Effect of Substrates Characteristics on Tribological Behaviors of AlTiN-Based Coated WC–Co Cemented Carbides

Tribological properties and wear resistance mechanism of WC-ZrO2-Al2O3 ceramics

Effects of CrMnFeCoNi additions on microstructure, mechanical properties and wear resistance of Ti(C,N)-based cermets

Tribological and Electrochemical Corrosion Behaviors of Cu-based Powder Metallurgy Composites Reinforced by In-Situ WC with Different Morphology

In Situ Synthesis and Tribological Characterization of TiC–Diamond Composites: Effect of the Counterface Material on Wear Rate and Mechanism

Effect of WC addition on microstructure and properties of laser melting deposited Ti6Al4V

Effect of TiCp Volume Fraction and WCp Addition on the Mechanical Properties of TiCp/Cr8Mo2VSi Composites

Effect of Ni content on the microstructure and properties of WCoB-TiC cermets

Excellent Tribological Properties and Unique Wear-Resistance Mechanism of Binderless Tungsten Carbide Prepared Via Two-Step Oscillatory Pressure Sintering

Effect of carbon content on the tribological behaviour of TiC x coatings prepared by reactive HiPIMS

Mechanical and tribological properties of WC particles reinforced Cu-20Zn matrix composites

Enhancing the wear resistance of sintered WC–Co composite by adding pseudo-elastic TiNi constituent