Abstract:The unsatisfactory high-temperature performance of commonly used silicon carbide (SiC)-based ceramics calls for a novel approach for their reinforcement. We present the in situ preparation of a SiC-based composite with uniformly dispersed titanium boride (TiB2) particles using titanium carbide and boron carbide as raw materials. Notably, the uniform incorporation of 25 wt%TiB2 results in the SiC–TiB2 composite with excellent tribological and self-lubricating properties at high temperatures. The SiC–TiB2 composite shows a friction coefficient of 0.20 and a specific wear rate of 5.77 × 108 mm3/(N mm), which are 4.75 times and ~ 5.2 times lower than that of the bare SiC ceramic at 1000 °C, respectively. The wear mechanism of a self-mated couple of the SiC–TiB2 composite is unraveled to be the tribo-oxidization. Since intimate contact exists between the oxidizing layer and the transitional layer of the fractured surface, the friction surface possessing plastic deformation properties may transit from brittle to plastic or elastic. The "Pin Effect" exhibited by TiB2 particles in the SiC–TiB2 composite deflects the crack propagation route. Meanwhile, a change in stress distribution, a decrease in the stress intensity of slight crack frontier, and an increase in "the threshold value" of crack propagation occur. The type (I + II) and type (I + III) complex cracks in fracture mechanics propagate non-flatly in the wearing process of the self-mated couple of the SiC–TiB2 composite. Besides, a fine yield deformation zone exists on the crack tip. Consequently, the "threshold value" of crack propagation fluctuates dynamically between "upper bound value" and "lower bound value" following the change in the valid length of actual crack propagation, thus delaying the fracture of the SiC–TiB2 composite.

Excellent Tribological Properties and Unique Wear-Resistance Mechanism of Binderless Tungsten Carbide Prepared Via Two-Step Oscillatory Pressure Sintering

Tailoring Mechanical and Tribological Properties of Oscillatory Pressure Sintered Binderless WC Ceramics with Expanded Graphite Addition

Extraordinary High-Temperature Mechanical Properties in Binder-Free Nanopolycrystalline WC Ceramic

Tribological properties and wear resistance mechanism of WC-ZrO2-Al2O3 ceramics

Preparation of Ultra-Fine ATC Ceramics and Analysis of Its Dry-Sliding Wear Behavior

Enhanced mechanical and tribological properties of oscillatory pressure sintered WC–GNPs composites

Oscillatory pressure sintering of binderless tungsten carbide

Research On Wear Behavior Of Atc Cermet Material

A novel sintering method of Al2O3/SiCw ceramic composites with improved wear resistance: Oscillatory pressure‐assisted sinter forging

Tribological behaviors of vacuum hot-pressed ceramic composites with enhanced cyclic oxidation and corrosion resistance

Ultrafine‐grained WC‐based Ceramics Prepared Via Two‐step Oscillatory Pressure Sintering

Binderless nanocrystalline tungsten carbide with enhanced hardness induced by high-pressure sintering

In situ preparation of a SiC–TiB2 composite and its wear fracture mechanism at high temperatures

Effect of fiber orientation on tribological properties of fiber reinforced C/C‐SiC composites mated with ceramic ball

Effect of tungsten carbide content on the tribological behavior of TiB2–TiC-based cermets

Tribological performance of DLC-coated ceramics against cemented carbide under dry sliding conditions

High-pressure synthesis and performance analysis of WC-cBN-MoS2 self-lubricating ceramic composites

Tribological behavior of aluminum matrix composites reinforced with ceramic particulates in dry sliding against a semimetallic friction material

Advanced ceramic and its wear resistance

Microstructure and mechanical properties of oscillatory pressure sintered WC ceramics with different carbon sources

Directional diffusion of carbon atoms and lattice distortion in the high-speed changing dynamic temperature field – A novel method to manufacture high tribological performance cermets