Abstract:This paper assessed the growth of CVD composite coatings on three kinds of cermets and the subsequent high-temperature frictional properties. The carbon to nitrogen ratios (C: N) of Ti(C1-x, Nx) powders added to these three cermets were 5:5,7:3 and 10:0, respectively. It was prepared by powder metallurgy. The TiN/α-Al2O3/Ti(C, N)/TiN multilayer coatings were deposited on different Ti(C, N)-based cermets. The results showed that the crystallinity of the composite coating was affected by the contents of nitrogen content. The inner layer TiN coating exhibited a nano-columnar crystal structure, which detected (111) and (200) orientation texture by XRD. The α-Al2O3 coating and Ti(C, N) coating of the three specimens were coarse columnar crystal structures. The variation in the nitrogen content led to the different performances of the coating. Meanwhile, The CVD coating with a C/N ratio of 7:3 had the best comprehensive properties, because the substrate had similar grain-forming directions and more shape nucleation points. The Electron Backscattered Diffraction (EDSB)、Scanning Electron Microscope (SEM) and Energy Dispersive Spectrometer (EDS) were used to further analyze the microstructure of the samples. The Coating Al2O3 displayed excellent mud (100) value, which indicated that the preferred texture (100) existed and improved the performance of the Al2O3 coating. The adhesion strength of the composite coating on Ti(C0.7, N0.3)-based cermets is the highest. The high-temperature friction wear of the coating was further investigated. Group Y2, which expressed the sample of Ti(C0.7, N0.3)-based cermets CVD coating, demonstrated the lowest wear rate. All control groups’ wear mechanisms included abrasive wear, diffusion wear, and oxidation wear.

Research On Wear Behavior Of Atc Cermet Material

Preparation of Ultra-Fine ATC Ceramics and Analysis of Its Dry-Sliding Wear Behavior

Wear Behaviour and Microstructural Changes of SiCw-Al Composite under Unlubricated Sliding Friction

Wear Resistance of Tic Ceramic Particulate-Reinforced Metal Matrix Cermets

Advanced ceramic and its wear resistance

Preparation of Ultra-Fine WC-Co Cermet and Its Wear Behavior

Reciprocating Wear Performance and Interfacial Microstructure of a TiC–Ni 2 AlTi Cermet

Tribological characteristics of WC-Cr3C2-Ni cermet coatings under different wear parameters

Preparation, mechanical properties and wear resistance of dual-sized TiC particles reinforced high-entropy alloy cermet coating

Friction and wear behavior of Ti(C,N) self-lubricating cermet materials with multilayer core-shell microstructure

Study on the growth and wear behavior of the TiAlN-based composite coating deposited on TiCN-based cermets with different binder phase

Preparation, mechanical properties and enhanced wear resistance of TiC-Fe composite cermet coating

Microstructure, Mechanical Properties and Wear Behaviors of Ultrafine-Grain WC-Based Cermets with Different Binder Phases Fabricated by Spark Plasma Sintering

Wear Behaviors of Ticn Cermet under Different Concentrations of Abrasive Slurries from Carborundum, Corundum and Silica Sands

Friction and dry sliding wear behaviour of cermets

Effects of nano-Al2O3 addition on microstructure, mechanical properties, and wear resistance of Ti(C, N)-based cermets

The Influence of Powder Characteristics on Mechanical Properties of Al2O3–TiC–Co Ceramic Materials Prepared by Co‐coated Al2O3/TiC Powders

Study on the growth and wear characters of CVD coating deposited on Ti(C, N)-based cermets with adding different C/N ratios of Ti(C, N) powders

Abrasive Wear Behavior of Ticn Cermets under Water-Based Slurries with Different Abrasives

Investigation of Wear-Resistant Property of TiC/Fe Ceramic Coating Produced by Self-Propagating High-Temperature Synthesis

Comparisons of Microstructure and Properties of Three Cobalt-Based Cermets Deposited by High Velocity Oxy-Fuel Spraying Using Clad Powders