Abstract:TiC bonded diamond composites were prepared from a mixture of Ti, graphite, and diamond powders as raw materials, with Si as sintering additives, through high-temperature and high-pressure (HTHP) technology. The reaction between Ti and graphite under 4.5–5 GPa pressure and 1.7–2.3 kW output power can produce TiC as the main phase. The diamond particles are surrounded by TiC, and the interface is firmly bonded. The coefficient of friction (COF) of TiC–diamond composites with POM and PP balls decreases with increasing load for a specific friction velocity. However, the COF of TiC–diamond composites with agate, Cu and Al balls increases with the rising load because of the enhanced adhesive wear effect. The COF of PP, Cu and Al balls slightly increases with the increase in friction velocity at a certain load. SEM results show that the surface of agate balls has rough, pear-shaped grooves and shallow scratches. The scratches on the surface of POM balls are wrinkled. The PP balls have pear-shaped groove scratches on their wear surfaces. The wear mechanism of TiC–diamond composites with Cu ball pairs is primarily adhesive wear. The abrasion of TiC–diamond composites with Cu ball pairs remains almost unchanged as the load increases. However, the depth and width of the pear-shaped grooves on the wear surface of TiC–diamond composites are significantly increased. This phenomenon may be attributed to the high rotational speed, which helps to remove the residual abrasive debris from the friction grooves. As a result, there is a decrease in both the depth and width of the pear-shaped grooves, leading to a smoother overall surface. The wear mechanism of TiC–diamond composites with Al ball pairs is abrasive wear, which increases with an increasing load. When the load is constant, as the speed increases, the wear morphology of TiC–diamond composites with Al ball pairs transitions from rough to smooth and then back to rough again. This phenomenon may be attributed to the wear mechanism at low speeds being groove wear and adhesive wear. As the speed increases, the wear particles are more easily removed from the wear track, leading to a reduction in abrasiveness. As the speed increases, the wear surface becomes roughened by a combination of grooves and dispersed wear debris. This can be attributed to the increased dynamic interaction between surfaces caused by higher speed, resulting in a combination of abrasive and adhesive wear. In addition, Cu and Al ball wear debris appeared as irregular particles that permeated and adhered to the surface of the TiC phase among the diamond particles. The results suggest that TiC–diamond composites are a very promising friction material.

In situ preparation of a SiC–TiB2 composite and its wear fracture mechanism at high temperatures

High-performance TiN Reinforced Sialon Matrix Composites: A Good Combination of Excellent Toughness and Tribological Properties at a Wide Temperature Range

Microstructure and Tribological Properties of Reactive Hot Pressed TiN–TiB2 Composites Incorporated with or Without MoSi2 from Room Temperature to 800°C

Preparation and Characterization of In Situ (TiC-TiB2)/Al-Cu-Mg-Si Composites with High Strength and Wear Resistance

Evaluation on tribological characteristics of (TiC+TiB)/Ti-6Al-4V composite in the range from 25 C to 600 C

Microstructure and Wear Behavior of Ti-xFe-SiC In Situ Composite Ceramic Coatings on TC4 Substrate from Laser Cladding

The tribological behavior evolution of TiB2/Al composites from running-in stage to steady stage

In-situ friction and wear study of SiCα/SiCβ and Al2O3-TiC-Co composite ceramics

Synthesis and Tribological Behaviors of Ti 3 SiC 2 Material Prepared by Vacuum Sintering Technique

In Situ Synthesis and Tribological Characterization of TiC–Diamond Composites: Effect of the Counterface Material on Wear Rate and Mechanism

Novel Ti3SiC2-(Ti, Zr)B2 Toughened (ti, Zr)C-based Composites with Enhanced Mechanical Properties Fabricated by Dual in Situ Reactions Hot-Pressing at Low Temperature

Self-lubricating behavior caused by tribo-oxidation of Ti3SiC2/Cu composites in a wide temperature range

Temperature dependence of fracture behavior of in situ synthesized TiC/Ti-alloy matrix composite

High temperature and room temperature tribological behaviors of in-situ carbides reinforced Ni-based composites by reactive sintering Ni and Ti2AlC precursor

Microstructures and mechanical properties of in-situ SiC-TiB2 ceramic composites fabricated by reactive melt infiltration

Co-construction of microstructure evolution and wear resistance of in-situ TiBw/TA15 composites with network structure

Microstructure, mechanical and friction-wear properties of SiC-WC composite with Al and C as sintering aids

Synthesis and Tribological Characterization of Ti3SiC2/ZnO Composites

Analysis of oxidation behavior of laser cladding SiC-Ti based composite strengthening coating

The Microstructure, Mechanical, and Friction-Wear Properties of Boron Carbide-Based Composites with TiB2 and SiC Formed In Situ by Reactive Spark Plasma Sintering

Bioinspired PcBN/hBN Fibrous Monolithic Ceramic: High-temperature Crack Resistance Responses and Self-Lubricating Performances