Abstract:In this paper, SiCp aluminium matrix composites were used as the matrix, and AlSi10Mg powder, which has a relatively similar coefficient of thermal expansion to that of the matrix, was used to prepare laser cladding Al-based coatings. The results show that the optimal process parameters are P = 4400 W, Vf = 11.3 g·min−1, and VS = 1800 mm·min−1, and, although the hardness of the coatings is lower than the hardness of the substrate, it reduces the generation of defects such as cracks and porosity. With the increase in WC reinforced phase and the hardness of the coatings, wear resistance increases, the granular cytocrysts are transformed into rod-like cytocrysts, and at the same time generate the dendritic crystals, and the undergo grain refining and generate the new phases such as Al4C3, Al4SiC4. There is no obvious defect in AlSi10Mg + 40%WC coatings, the macro morphology of the coatings is good, there is no spalling in the friction wear morphology, and the wear resistance is excellent, but there are obvious cracks and obvious spalling in the coatings of AlSi10Mg + 60%WC. Compared to the matrix hardness of 171.61 HV, the hardness of the 20%WC cladding layer increased by a factor of 1.06, while the hardness of the 40%WC cladding layer increased by a factor of 1.65 and that of the 60%WC cladding layer increased by a factor of 1.8. In terms of wear, compared to a substrate wear amount of 9.36 mg, the wear for the 20%WC cladding layer was reduced to 6.13 mg (34.5% less than the substrate), for the 40%WC cladding layer it was reduced to 4.58 mg (51.06% less than the substrate), and for the 60%WC cladding layer it was reduced to 7.35 mg (21.47% less than the substrate). The quality of the coatings decreases although the hardness is higher than that of AlSi10Mg + 40%WC. The comprehensive performance of AlSi10Mg + 40%WC coatings is optimal.

Microstructure, mechanical and friction-wear properties of SiC-WC composite with Al and C as sintering aids

Wear Behaviour and Microstructural Changes of SiCw-Al Composite under Unlubricated Sliding Friction

Mechanical and Tribological Properties of SiC Whisker‐reinforced SiC Composites Via Oscillatory Pressure Sintering

Mechanical and tribological properties of SiC whiskers reinforced SiC composites via oscillatory pressure sintering

Effect of the amount of SiC particles on the microstructure, mechanical and wear properties of FeMnCoCr high entropy alloy composites

Microstructure, Mechanical and Tribological Properties of CrSiC Coatings Sliding Against SiC and Al2O3 Balls in Water

Investigation of Mechanical and Tribological Properties of Al–7 Wt.% Si alloy Metal Matrix Composites Reinforced with SiC

Mechanical and Tribological Behaviors of Hot-Pressed SiC/SiCw-Y2O3 Ceramics with Different Y2O3 Contents

Effect of Spherical WC Content on the Microstructure and Properties of SiCp Aluminium Composite Material

Microstructure and Mechanical Properties of HfC-SiC Ceramics Influenced by WC Addition

Effect of SiC on the anti-ablation resistance and flexural strength of (Hf-Ta-Zr)C-C/C composites

Effects of foam structure on the wear behavior of co-continuous SiC3D/Al composite materials

Correlation between phase content and mechanical properties of SiCw- ZTA composites sintered by SPS

Tribological Behavior of Liquid Phase Sintered SiC Ceramics Under Dry Condition

Preparation, mechanical properties, and toughening mechanisms of SiCw/SiCp‐reinforced zirconia‐toughened alumina ceramics

Microstructure and mechanical properties of SiC reinforced AlSi10Mg composites fabricated by laser metal deposition

Effect of SiC Contents on Wear Resistance Performance of Electro-Codeposited Ni-SiC Composite Coatings

In-situ friction and wear study of SiCα/SiCβ and Al2O3-TiC-Co composite ceramics

Microstructure, mechanical properties and thermal conductivity of (Ti0.5Nb0.5)C–SiC composites

Microstructures and Properties of WC-10 wt.%CoCrFeNiAlx Composite Cemented Carbides

Microstructure and wear resistance of in-situ synthesized stellate Mo2C reinforced WC/amorphous composite coatings by resistance seam welding (RSW)