Abstract:In this paper, a multiple-ring-modulated junction termination extension (MRM-JTE) technology for large-area silicon carbide PiN rectifier rated at 4500 V is proposed and experimentally investigated using a standard two-zone JTE (TZ-JTE) process without extra process steps or masks. Multiple modulation rings embedded inside JTE region, which is similar to varied lateral doping technology widely used in silicon devices, form a gradual decrease of effective charges in the termination region. MRM combines the advantages of two termination techniques, namely, ring-assisted JTE and space-modulated JTE, to enlarge the optimum JTE-dose window with high reverse blocking voltage in comparison with conventional TZ-JTE. A breakdown voltage of 4940 V at a leakage current of 1 mu A is achieved from fabricated MRM-JTE rectifiers with a 36-mu m-thick N-epilayer doped to 1.8 x 10(15) cm(-3), which is 92% of the ideal parallel-plane value. A forward current of 50 A has been measured at a forward voltage drop of 3.9 V for devices with an active anode area of 9.2 mm(2), corresponding to low differential on-resistance of 1.8 m Omega.cm(2). The simulation and experimental results show that the proposed device exhibits approximately 2 times JTE dose tolerance window improvement with respect to the breakdown voltage of 4500 V.

Bevel Junction Termination Extension—A New Edge Termination Technique for 4H-Sic High-Voltage Devices

A New Edge Termination Technique for High-Voltage Devices in 4H-Sic–multiple-floating-zone Junction Termination Extension

Area-Efficient Bevel-Edge Termination Techniques for SiC High-Voltage Devices

Hybrid Termination with Wide Trench for 4H-Sic Super-Junction Devices

Etched Junction Termination Extension With Floating Guard Rings And Middle Rings For Ultrahigh-Voltage 4h-Sic Pin Diodes

An Improved Composite JTE Termination Technique for Ultrahigh Voltage 4H-Sic Power Devices

Improved Etched Multistep JTE for UHV SiC Power Devices

An Effective High-Voltage Termination for Sic Planar Pn Junctions for Use in High-Voltage Devices and Uv Detectors

Expanding the Dose Window of Step-Etched Space-Modulated JTE for Ultrahigh Voltage 4H-Sic Devices

A Multiple-Ring-Modulated JTE Technique for 4H-Sic Power Device with Improved JTE-Dose Window

Single-Implant, Field Plate and Guard Rings Assist Multi-Zone Graded Jte for 4H-Sic P-I-N Diodes

High Voltage SiC JBS Diodes with Multiple Zone Junction Termination Extension Using Single Etching Step

Orthogonal Positive-Bevel Termination for Chip-Size SiC Reverse Blocking Devices

Development of G10kv 4H-Sic SBD Junction Extension Termination

Two-mesa, guard rings assisted two-zone JTE for ultrahigh-voltage(>10kv) 4H-SiC p-i-n diodes

Multi-Step Junction Termination Extension Design and Simulation Study for 4H-Sic Schottky Barrier Diode

Sic Symmetric Blocking Terminations Using Orthogonal Positive Bevel Termination And Junction Termination Extension

Step JTE, an Edge Termination for UHV SiC Power Devices with Increased Tolerances to JTE Dose and Surface Charges

Characterization and Fabrication of the CFM-JTE for 4H-Sic Power Device with High-Efficiency Protection and Increased JTE Dose Tolerance Window

Evaluation of Termination Techniques for 4H-Sic Pin Diodes and Trench JFETs

Modeling and Optimization of Smoothly Tapered Junction Termination Extension for High-Voltage SiC BJTs and Thyristors by Simulation