Abstract:Uniform distribution of Cr2AlC MAX phase plays a crucial role in evolution of microstructure and mechanical properties. The incorporation of Cr2AlC MAX phase with and without milling in conventionally sintered WHA significantly enhances refinement of W‐grains. Combination of grain size refinement and dispersion strengthening results in the improvement of tensile properties This study focuses on the role of Cr2AlC‐MAX phase incorporation on the density, phase composition, microstructure, and mechanical properties of 90W‐6Ni‐2Fe‐2Co heavy alloy. The blended powders are ball milled in a high‐energy ball mill up to 40 h, compacted, and sintered at 1500 °C. The mechanical alloying results in a refined microstructure with uniform distribution of W, matrix, and dispersoids. The minimum grain size of W (14.7 ± 5.6 μm) is obtained in 2 wt% Cr2AlC‐containing tungsten alloy prepared from 40 h‐milled powders. Among the investigated alloys, 1 wt% Cr2AlC‐incorporated samples exhibit maximum compressive stress (2026 MPa). The incorporation of fine Cr2AlC as dispersoids is found to be beneficial in improving the strength as well as ductility of WHAs. The best combination of yield strength (553.4 MPa), ultimate tensile strength (1011.2 MPa), ductility (11.4%), and product of strength and elongation (11.5 GPa%) is found in alloy prepared from 40 h milled 90W‐4.8Ni‐1.6Fe‐1.6Co‐2Cr2AlC. The improved tensile strength in Cr2AlC‐incorporated WHAs may be attributed to the combined effect of grain size refinement and dispersion strengthening. Overall, the combination of ball milling and Cr2AlC incorporation in tungsten‐heavy alloys is found to be effective in developing a novel W‐based alloy system for strategic applications.

Effect of Ball Milling Time on Microstructure and Properties of Laves Phase NbCr2 Alloys Synthesized by Hot Pressing

Long-term Ball Milling and Hot Pressing of In-Situ Nanoscale Tungsten Carbides Reinforced Copper Composite and Its Characterization

Investigation of a Hot-Pressed Nb–Ti–Al Alloy: Mechanical Alloying, Microstructure and Mechanical Property

Influence of Ball Milling Processing on the Microstructure and Characteristic of W–Nb Alloy

Preparation of Nb3al by High-Energy Ball Milling and Superconductivity

Preparation of Nb 3 Al Superconductor by Powder Metallurgy and Effect of Mechanical Alloying on the Phase Formation

Fabrication of nanocrystalline supersaturated W–Al alloys with enhanced thermal stability and high sinterability

Effect of High Pressure on Microstructure of Crystallizing Amorphous Nd9Fe85B6 Alloy

Effect of Cr on solidification structure and microhardness of Al-Ni alloy

EFFECTS OF HIGH-ENERGY BALL MILLING ON THE STRUCTURE AND PROPERTY OF A MULTIPHASE Al3Ti-BASED INTERMETALLIC ALLOY

Effect of Microstructure and Performance of Nb–Cr–Fe–Ni Quaternary Alloys with the Variation of Niobium Element Content

Micromechanism in fracture toughness of NbCr2 laves phase improved by nickel alloying: first-principles calculation

Formation of Nanocrystalline Fcc Phase by Mechanically Driven Crystallization

Microstructure and property of Al67Mn8Ti24Nb1 intermetallics consolidated with metasable powder

Microstructure and Properties of In-Situ TiC Reinforced Copper Nanocomposites Fabricated Via Long-Term Ball Milling and Hot Pressing

Fracture toughness of hot-pressed Al67Mn8Ti24Nb1 intermetallics consolidated with metastable powder

Effects of high-energy ball milling on structure and mechanical properties of L12 intermetallic compound Al67Mn8Ti25

Microstructure and Mechanical Properties of the Powder Metallurgy Nb-16Si-24Ti-2Al-2Cr Alloy

Effect of High‐Energy Ball‐Milling Duration on Densification, Microstructure, and Mechanical Properties of Cr2AlC‐Dispersed 90W‐6Ni‐2Fe‐2Co Heavy Alloys

FRACTURE TOUGHNESS OF HOT-PRESSED Al67Mn8Ti24Nb1 INTERMETALLICS CONSOLIDATED WITH METASTABLE POWER

Optimization of the Microstructure and Mechanical Properties of a Laves Phase-Strengthened Hypoeutectic NiAl/Cr(Mo,W) Alloy by Suction Casting