Abstract:Due to their potential improvement of high-temperature properties, the refractory metal hafnium (Hf) and the rare earth holmium (Ho) have attracted much attention. In the present research, NiAl-Cr(Mo) eutectic alloys with different Ho and Hf additions were fabricated by conventional smelting method and heat-treated to study the synergetic influence of strengthening elements and heat treatment. The samples were characterized using XRD, SEM, and TEM, and the three-point bending test was performed to obtain fracture toughness. The results demonstrate that Hf addition leads to the formation of Ni2AlHf Heusler phase and that Ho promoted the formation of Ni2Al3Ho phase. The microstructure of the alloy is affected by thermal treatment, with the coarsening of eutectic lamellae after heat treatment. The mechanical properties are improved by Hf and Ho additions, with increased fracture toughness. Overall, this study provides insights into the microstructure and properties of NiAl-Cr(Mo) eutectic alloys and highlights the potential of Hf and Ho addition to improve room-temperature properties. Specifically, the as-cast NiAl-Cr(Mo)-Hf eutectic alloy contains a relatively fine NiAl/Cr(Mo) eutectic lamella but coarse eutectic cell with Ni2AlHf phase embellished along the cell boundary. Minor Ho addition induces the formation of Ni2Al3Ho phase, which leads to the coarsening of the intercellular region but contributes to the refining of eutectic cell. In addition, the synergetic effect of Ho and Hf promotes the precipitation of Ni2Al3Ho and Ni2AlHf phases in the intercellular zone and increases the interface dislocations. Heat treatment benefits the solid solution of Ni2Al3Ho and Ni2AlHf phases, which improves their size and distribution by secondary precipitation. The Ni2AlHf phase in the NiAl-Cr(Mo)-Hf eutectic alloy becomes fine and uniformly distributed, but the NiAl/Cr(Mo) eutectic lamella in the eutectic cell becomes coarse. In comparison, heat treatment mainly optimizes the size and distribution of the Ni2Al3Ho and Ni2AlHf phases in the NiAl-Cr(Mo)-Hf-Ho eutectic alloy. Furthermore, heat treatment helps to eliminate the interface dislocations in the large NiAl precipitates and the NiAl/Cr(Mo) phase interfaces, which also contributes to fracture toughness by decreasing stress concentration. Minor Ho addition decreases the fracture toughness of as-cast NiAl-Cr(Mo)-Hf eutectic alloy from 6.7 to 6.1 MPa·m1/2, which should be ascribed to the coarsened intercellular region including aggregated Ni2Al3Ho and Ni2AlHf phases. However, minor Ho-doped NiAl-Cr(Mo)-Hf eutectic alloy obtained the highest fracture toughness of 8.2 MPa·m1/2 after heat treatment. This improved fracture toughness should be mainly attributed to the refined and well-distributed Ni2Al3Ho and Ni2AlHf phases in the heat-treated NiAl-Cr(Mo)-Hf-Ho eutectic alloy.

Optimization of the Microstructure and Mechanical Properties of a Laves Phase-Strengthened Hypoeutectic NiAl/Cr(Mo,W) Alloy by Suction Casting

Microstructure Evolution and Mechanical Properties' Improvement of NiAl–Cr(Mo)–Hf Eutectic Alloy During Suction Casting and Subsequent HIP Treatment

Microstructure and Mechanical Properties of NiAl–Cr(Mo)/Nb Eutectic Alloy Prepared by Injection-Casting

Microstructure and compressive properties of NiAl–Cr(Mo)–Dy near eutectic alloy prepared by suction casting

Microstructure and Mechanical Properties of Hf and Ho Doped NiAl–Cr(Mo) Near Eutectic Alloy Prepared by Suction Casting

Microstructure and Mechanical Properties of Zirconium Doped Nial/Cr(Mo) Hypoeutectic Alloy Prepared by Injection Casting

Microstructure and Mechanical Properties Determined in Compressive Tests of Quasi-Rapidly Solidified NiAl-Cr(Mo)-Hf Eutectic Alloy after Hot Isostatic Pressure and High Temperature Treatments

Influence of Strengthening Elements and Heat Treatment on Microstructure and Fracture Toughness of NiAl-Cr(Mo)-Based Eutectic Alloy

Regulation on Microstructures and Properties of Hypereutectic Al–3.5Fe–2.5Ni Alloy by Controlled Diffusion Solidification

Microstructure Evolution and Elevated Temperature Compressive Properties of a Rapidly Solidified NiAl–Cr(Nb)/Dy Alloy

MICROSTRUCTURE AND MECHANICAL PROPERTIES OF LAVES PHASE STRENGTHENING NiAl BASE COMPOSITE FABRICATED BY RAPID SOLIDIFICATION

Microstructure and Mechanical Properties of Rapidly Solidified NiAl–Cr(Mo) Eutectic Alloy Doped with Trace Dy

Microstructure Characteristics and Compressive Properties of NiAl-based Multiphase Alloy During Heat Treatments

Microstructure and properties of QAl10-4-4 alloy fabricated by rheological squeeze casting

Microstructure Evolution and Toughening Mechanism of a Nb-18Si-5HfC Eutectic Alloy Created by Selective Laser Melting

Phase constitution, microstructure and mechanical properties of a Ni-based superalloy specially designed for additive manufacturing

Microstructure and Mechanical Properties of the Powder Metallurgy Nb-16Si-24Ti-2Al-2Cr Alloy

Development of a novel high strength Al-Si-Cu-Ni alloy by combining micro-alloying and squeeze casting

Improvement of Compressive Strength and Ductility in NiAl–Cr(Nb)/Dy Alloy by Rapid Solidification and HIP Treatment

Effects of Hip and Heat Treatment on Microstructure and Compressive Properties of Rapidly Solidified Nial-Cr(Mo)-Hf Eutectic Alloy

Effect of Growth Rate on the Tensile Properties of DS NiAl/Cr(Mo) Eutectic Alloy Produced by Liquid Metal Cooling Technique