Abstract:In this work, 7075 Al alloy, a high-strength wrought aluminum alloy with high hot tearing sensibility, was used in the squeeze casting of an asymmetric part. The solidification defects, microstructures and mechanical properties of the part solidified under different forming pressures were studied. Furthermore, the uniformities of the microstructures, mechanical properties and the solidification mechanisms were investigated. Results show that increasing the forming pressure is helpful to improve the liquid/solid feeding for counteracting the particularly serious shrinkage during the wide mushy zone of 7075 Al alloy. Therefore, the solidification defect can be avoided. Moreover, increasing the forming pressure is helpful to not only obtaining fine equiaxed grains, but also diminishing the intergranular segregation of alloying elements. With the increasement of forming pressures, the strengths of the part increased, along with the decreases in the ductile due to the work hardening resulted from the serious solid feeding. The microstructures and mechanical properties are impacted by the solidification rate of the melt at different regions. When the forming pressure was 150 MPa, fine microstructures and excellent mechanical properties were obtained. The uniformity of the microstructures and mechanical properties are dominated by the solidification location sequence of the melt. Further on, it is determined by the thermal gradient of the melt at different locations. For 7xxx series alloys, more solid feeding is needed for counteracting the serious shrinkage at the first solidified regions, causing a work hardening and associated strengths increasements. A near uniform part thickness and direct feeding loads are appreciated to improve the uniformities. In this work, the optimal tensile properties tested in the part were tested to be as follows: the yield strength (YS), ultimate tensile strength (UTS), and elongation (EL) are 345.5 MPa, 483.2 MPa, and 7.6%, respectively. The UTS uniformity is tested to be 86.4%.

Microstructure and properties of QAl10-4-4 alloy fabricated by rheological squeeze casting

Fabrication of Nanocrystalline Zro2 Particle Reinforced Aluminum Alloy Composite by Squeeze Casting Route

Study on Microstructure Distribution of Al-Cu-Mg Alloy in Squeeze Casting Process

Microstructure and Mechanical Properties of Squeeze Casting Quasicrystal Reinforced AZ91D Magnesium Matrix Composites

Optimization of the Microstructure and Mechanical Properties of a Laves Phase-Strengthened Hypoeutectic NiAl/Cr(Mo,W) Alloy by Suction Casting

Microstructure and Mechanical Properties of Squeezing Casting Mg-Nd-Gd-Zn-Zr Alloy

Effect of pressure on the microstructure refinement, solidification mechanism and fracture behavior of wrought Al-Zn-Mg-Cu alloys prepared by squeeze casting

Experimental study of squeeze casting of ZK60 magnesium alloy

Multiple cycles of combined cold rolling and short-time annealing on the microstructure and properties evolution of NiAl bronze

Development of a novel high strength Al-Si-Cu-Ni alloy by combining micro-alloying and squeeze casting

Microstructure and mechanical properties of squeeze-cast Al−5.0Mg−3.0Zn−1.0Cu alloys in solution-treated and aged conditions

Microstructure Evolution and Mechanical Properties' Improvement of NiAl–Cr(Mo)–Hf Eutectic Alloy During Suction Casting and Subsequent HIP Treatment

Microstructure, Mechanical and Tribological Properties of Nickel-Aluminium Bronze Alloys Developed Via Gas-Atomization and Spark Plasma Sintering

Microstructure characteristics and strengthening mechanism of semisolid CuSn10P1 alloys

Developing High Performance Mechanical Properties at Elevated Temperature in Squeeze Cast Al-Cu-Mn-Fe-Ni Alloys

Microstructures, mechanical properties and solidification mechanism of a hot tearing sensitive aluminum alloy asymmetric part fabricated by squeeze casting

Numerical Simulation and Experimental Investigation of Microstructure Evolution and Flow Behavior in the Rheological Squeeze Casting Process of A356 Alloy

Hot tensile and fatigue behaviour of zinc–aluminum alloys produced by gravity and squeeze casting

Achieving refined microstructures and improved mechanical properties in a cup-shaped Mg-Gd-Y-Zr alloy casting by novel near-liquidus squeeze cast process

The effect of squeeze casting process on the microstructure, mechanical properties and wear properties of hypereutectic Al–Si–Cu–Mg alloy

Microstructure and mechanical properties of an aluminum alloy reinforced by Al–Ni–Co–Mn quasi-crystalline