Abstract:Powder metallurgy is an effective method to produce Cu-Al-based alloys for automotive and aerospace engineering components. The finer grain size, low cost, and low-temperature synthesis make this process more suitable than the other conventional production method such as melting and casting. The addition of Ni (austenite stabilizer) into the Cu increases the stability of Cu and refines the grain size. Again, the addition of Ni into the Cu-Al alloy increases the strength and hardness. In the present work, Cu-12Al alloys are developed by varying the wt.% of Ni content from 0 to 8 using powder metallurgy process through mechanical alloying method. Mechanical alloyed powder mixture is compacted by applying a load of 5 tons and sintered at 850 °C for 1 h under nitrogen atmosphere. It is found that α-Cu, γ2-Cu9Al4, and NiAl phases are presented in the Cu-12Al-Ni alloy which influences the properties of the alloy. The theoretical, sintered, and relative density values are decreased with increasing the wt.% of Ni content. However, the Vickers hardness of the alloy is improved by increasing the wt.% of Ni content up to 4 wt.% and then reduced for 8 wt.% of Ni content due to the coarsening and network-type structure of the NiAl phase. A higher amount of wear loss or wear rate is observed for the Cu-12Al and Cu-12Al-2Ni alloy than the Cu-12Al-4Ni and Cu-12Al-8Ni alloy. The presence of oxygen peaks in the EDS analysis revealed that an oxidative type of wear is occurred for the Cu-12Al alloy samples with varying the wt.% of Ni content. The electrochemical corrosion analysis revealed that the rate of corrosion is higher for Cu-12Al alloy without Ni. However, the rate of corrosion is reduced by increasing the wt.% of Ni content from 2 to 8.

Microstructure, Mechanical and Tribological Properties of Nickel-Aluminium Bronze Alloys Developed Via Gas-Atomization and Spark Plasma Sintering

Tailoring microstructure of a nickel aluminium bronze by hot extrusion and its impact on mechanical and corrosion behaviour

Effect of Al/Ni Ratio on the Microstructure and Properties of Nickel-Aluminum Bronze Alloys

Enhanced mechanical properties in nickel-aluminium bronze alloy via wire arc additive manufacturing with follow-weld forced cooling

Mechanical Properties and Oxidation Characteristics of TiNiAl(Nb) Intermetallics

Experimental investigation on wear resistance and corrosion behavior of nickel-aluminum bronze alloy fabricated by wire-arc additive manufacturing

Experimental and DFT Investigations of AlNbTiVZr High Entropy Alloys with Excellent Mechanical Properties

Effect of process parameters on microstructure and mechanical properties of a nickel-aluminum-bronze alloy fabricated by laser powder bed fusion

High Wear Resistance and Mechanical Performance of NiAl Bronze Developed by Electron Beam Powder Bed Fusion

Characterization of microstructure and wear behavior of nickel modified Zn-27% Al alloy casting

The constitutive relations and thermal deformation mechanism of nickel aluminum bronze

Enhancing microstructure and mechanical properties of nickel aluminium bronze alloy through tin addition

Microstructure and Mechanical Properties of Cu–12Al–xNi Alloy Prepared Using Powder Metallurgy

Micro-alloying effects of Ni on the microstructure and mechanical properties of an Al-Zn-Mg-Cu-Sc-Zr alloy

Improved strength in nickel‐aluminum bronze/steel bimetallic component fabricated using arcing-wire arc additive manufacturing with alternating deposition strategy

Multiple cycles of combined cold rolling and short-time annealing on the microstructure and properties evolution of NiAl bronze

Microstructure and properties of a novel ultra-high strength, high elasticity and high plasticity Cu–20Ni–20Mn-0.3Nb-0.3Cr-0.1Zr alloy

Microstructural evolution and mechanical properties of Ni/Al reactive nanolaminates with different NixAly intermetallic phases

Microstructure, Mechanical, and Tribological Relationship in Cu-12Al-Ni Alloy with Respect to the Variation of Ni Content

Microstructural Analysis, Tribological, and Corrosion Behavior of Nix-Tiy Alloys Deposited Using μ-Plasma Additive Manufacturing Process

Effect of heat treatment on the gas-atomized nickel‐aluminum bronze feedstock powders for cold spray