Abstract:Squeeze casting process can effectively resolve the casting difficulties for wrought aluminum alloys by pressurized solidification. The effects of applied pressure (0.1-125 MPa) on the microstructure refinement, non-equilibrium eutectic phase aggregation and fracture behavior of Al-Zn-Mg-Cu alloys prepared by squeeze casting were investigated through metallography, scanning electron microscopy and energy dispersive spectroscopy. The results showed that the primary α-Al grains transformed from coarse dendrites to refined equiaxed grains with increasing pressure. Considerable primary refinement was achieved at 100 MPa, with a significant decrease by 63% in the average grain size from 273 μm to 101 μm; the non-equilibrium eutectic phases were homogenized and refined, and almost dissolved into the Al matrix after T6 heat treatment. The mechanism of solidification behaviors in pressurized solidification was elucidated. Firstly, the applied pressure increased the thermodynamic driving force to promote primary grain nucleation. Secondly, the solute diffusion and constitutional undercooling at the front of the solid/liquid interface front were inhibited by pressure, and grain growth in a dendritic structure was thus restrained. Thirdly, interdependence theory and thermodynamic calculations were conducted to quantitatively describe the primary grain size changes under pressurized solidification. Lastly, the ternary eutectic reaction L → α-Al + T-Mg (Al, Zn, Cu) 2 + Al 2 Cu and binary eutectic reaction L→ α-Al + Al 7 Cu 2 Fe were suppressed by the reduced solute segregation. Furthermore, when the pressure increased from 0.1 MPa to 125 MPa, the ultimate tensile strength was raised from 428 MPa to 538 MPa, almost approaching that of samples by forging process. The refined eutectic phases decreased stress concentration and improved fracture behaviors.

Study on Microstructure Distribution of Al-Cu-Mg Alloy in Squeeze Casting Process

Experimental study of squeeze casting of ZK60 magnesium alloy

Effect of Mg addition on microstructure and mechanical properties of Al-Si-Cu-Fe alloy with squeeze casting

Microstructure and Mechanical Properties of Squeezing Casting Mg-Nd-Gd-Zn-Zr Alloy

Developing high performance squeeze cast Al-Cu alloys with high Fe and Cu contents

The effect of squeeze casting process on the microstructure, mechanical properties and wear properties of hypereutectic Al–Si–Cu–Mg alloy

Effect of pressure on the microstructure refinement, solidification mechanism and fracture behavior of wrought Al-Zn-Mg-Cu alloys prepared by squeeze casting

Microstructure and Mechanical Properties of Squeeze Casting Quasicrystal Reinforced AZ91D Magnesium Matrix Composites

Study on Pressurized Solidification Behavior and Microstructure Characteristics of Squeeze Casting Magnesium Alloy AZ91D

Numerical Simulation and Experimental Investigation of Microstructure Evolution and Flow Behavior in the Rheological Squeeze Casting Process of A356 Alloy

Microstructure and mechanical properties of squeeze-cast Al−5.0Mg−3.0Zn−1.0Cu alloys in solution-treated and aged conditions

Microstructure and properties of QAl10-4-4 alloy fabricated by rheological squeeze casting

Temperature Measurement and Microstructure Characteristics in Squeeze Casting Aluminum Alloy Parts

Microstructure simulation in pressurized solidification during squeeze casting of aluminum alloy A356

Squeeze casting for metal alloys and composites: An overview of influence of process parameters on mechanical properties and microstructure

Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

The Challenge and Progress in Macro- and Micro-modeling and Simulation of Squeeze Casting Process

Achieving refined microstructures and improved mechanical properties in a cup-shaped Mg-Gd-Y-Zr alloy casting by novel near-liquidus squeeze cast process

Numerical Simulation and Experimental Validation of Squeeze Casting of AlSi9Mg Aluminum Alloy Component with a Large Size

Macro and micro simulation and experiment study on microstructure and mechanical properties of squeeze casting wheel of magnesium alloy

Microstructures and Macrosegregation of Al–Zn–Mg–Cu Alloy Billet Prepared by Uniform Direct Chill Casting