Abstract:The present research computes the impact of process parameters of squeeze casting on AA8011/Si3N4/ZrO2 Hybrid Metal Matrix Composites (HMMCs). The melting temperatures (700 to 800°C), Si3N4 + ZrO2 (5 to 15 wt.%) and stirring speed (550 to 750 rpm) were selected as parameters for input. The AA8011 HMMCs were fabricated as per the combination of L9 input parameters, and they were subjected to Energy Dispersive X Ray Analysis (EDAX) and Scanning Electron Microscope (SEM) tests to compute the presence of wt.% of matrix and reinforcements and to confirm the uniform distribution of Si3N4 + ZrO2 in matrix AA8011. Besides, fabricated composites were subjected to tensile and micro hardness test after subjecting to Salt spray test (3.5% NaCl, 120 hours exposing duration and 1.2 kg/cm2 spray pressure) for computing the Ultimate Tensile Strength (UTS) and micro hardness. The Grey Relational Analysis (GRA) was employed for optimizing process parameters of squeeze casting on AA8011 based composites. The EDAX test results confirms that the increasing wt.% of silicon nitride and zirconium dioxide reinforcements enhances the presence of elements such as Si, N, Zr and O in manufactured composites. The higher dense reinforcements are uniformly distributed in the matrix AA8011 at the blend of input parameters of AA8011 composite. Based on the Taguchi approach, the medium level of melting temperature (750°C), higher level of wt.% of Si3N4 and ZrO2 reinforcements (15 wt.%) and higher level for speed of stirring (750 rpm) is the optimized combination parameters of squeeze casting for UTS and microhardness are identified. Based on the GRA technique, the influencing sequence are identified for squeeze casting process parameters are wt.% of Si3N4 + ZrO2 reinforcements, stirring speed and melting temperature for both UTS and Micro hardness. The contribution percentage of melting temperature, wt.% of reinforcements and stirring speed are 20.26%, 48.102% and 29.23% respectively. The confirmation test was done for optimized input parameters and it exhibit 56% higher UTS and 48.2% higher micro hardness of than AA8011 matrix material.

Experimental study of squeeze casting of ZK60 magnesium alloy

Microstructure and Mechanical Properties of Squeeze Casting Quasicrystal Reinforced AZ91D Magnesium Matrix Composites

Study on Pressurized Solidification Behavior and Microstructure Characteristics of Squeeze Casting Magnesium Alloy AZ91D

Squeeze Cast Mg-Zn Alloys for Bioapplications: Tensile Properties and Microstructure

Study on Microstructure Distribution of Al-Cu-Mg Alloy in Squeeze Casting Process

Determination of casting parameters of thick wall die-casting of magnesium alloy and simulation of its processing

Microstructure and Mechanical Properties of Squeezing Casting Mg-Nd-Gd-Zn-Zr Alloy

Effect of pressure on the microstructure refinement, solidification mechanism and fracture behavior of wrought Al-Zn-Mg-Cu alloys prepared by squeeze casting

Numerical and Experimental Investigation on Hot Backward Extrusion Process of Mg-Gd-Y-Zn-Zr Magnesium Alloy

Macro and micro simulation and experiment study on microstructure and mechanical properties of squeeze casting wheel of magnesium alloy

Research of Die-Casting Process of ZA85 Magnesium Alloys

The effect of squeeze casting process on the microstructure, mechanical properties and wear properties of hypereutectic Al–Si–Cu–Mg alloy

Experimental Study on the Heat Transfer Behavior and Contact Pressure at the Casting-Mold Interface in Squeeze Casting of Aluminum Alloy

Hot tensile and fatigue behaviour of zinc–aluminum alloys produced by gravity and squeeze casting

Research On Alloying Tecniques Of Mischmetal In Die Casting Magnesium Alloy

Numerical Simulation and Experimental Investigation of Microstructure Evolution and Flow Behavior in the Rheological Squeeze Casting Process of A356 Alloy

Squeeze casting for metal alloys and composites: An overview of influence of process parameters on mechanical properties and microstructure

Microstructure and Mechanical Properties of As-Cast and Hot Extruded–Sheared ZG61 Alloy

Numerical Simulation and Experimental Validation of Squeeze Casting of AlSi9Mg Aluminum Alloy Component with a Large Size

Optimization of Squeeze Casting Process Parameters on AA8011 Based Hmmcs Under NaCl Environment

AN ELASTIC-VISCOPLASTIC CONSTITUTIVE MODEL FOR SQUEEZE CASTING ALUMINUM ALLOY