Abstract:SiC fibers are widely used in composites exposed to high temperature oxidizing environments. The present study compares the oxidation behavior of SiC fibers and the associated changes in tensile strength upon their exposure to dry air and steam for up to 50 hours at temperatures from 950°C to 1350°C. In both cases, the scale thickness and oxide microstructure were analyzed by scanning electron microscopy. When the SiC fibers were oxidized in air, a crack-free amorphous oxide layer formed at temperatures up to 1200°C, whereas a cracked, crystallized oxide layer was found at 1350°C. By contrast under steam environment, a crystalline oxide forms at 950°C for oxidation times longer than 30 h. In both environments, the fiber strength decreased with increasing exposure time and temperature, the degradation being faster after oxidation in steam compared to dry air. This appears to relate to residual stress in the oxide scale and a reduction in the cross section of the load-bearing unoxidized SiC. An increase in defect size may also contribute to the loss of strength. The oxide scale follows parabolic growth kinetics in both dry air and in steam from 950°C to 1350°C, except at 1350°C for over 30 hours. The oxidation rate in steam is faster than that in dry air, with activation energies of 79.8±1.4 kJ/mol in steam and 153.6±3.4 kJ/mol in air, respectively. This work is relevant to the application of SiC fibers and SiC fiber reinforced composites in air and steam environments at high temperature.

Self-healing and failure behavior of yttrium silicate coated SiCf/SiC composites in air at elevated temperatures

Microstructure and oxidation behavior of SiOC coatings on C/C composites co-deposited with HMDS and TEOS by using CVD process

Oxidation behaviors of yttrium silicate modified SiCf/SiC composites in air and water‐oxygen environments

Long-term oxidation behaviors and strength retention properties of self-healing SiCf/SiC-SiBCN composites

A Novel Strategy to Improve the Corrosion Resistance of Sicf/Sic Composites in High-Temperature Combustion Environments by Cooperation of Self-Healing Sibcn and High-Stability Yb2si2o7

The impact of water and oxygen contents on the corrosion performance of yttrium silicate modified SiC f /SiC composites under high temperature conditions

Mechanical Properties and Oxidation Behaviors of Self-Healing SiC F /Sic-Sibcn Composites Exposed to H 2 O/O 2 /na 2 SO 4 Environments

Oxidation resistance of SiCf/SiC composites with a PyC/SiC multilayer interface at 500 °C to 1100°C

Influence of Oxidation Damages on Mechanical Properties of SiC/SiC Composite Using Domestic Hi-Nicalon Type SiC Fibers

The Oxidation Behavior and Corrosion Mechanism of SiC Matrix Ceramics in a High Temperature Wet Air Environment

Oxidation Behavior of SiC/SiC Composites in Air at High Temperature

Tensile Properties of Two-Dimensional Carbon Fiber Reinforced Silicon Carbide Composites at Temperatures Up to 1800 °C in Air

Fabrication and oxidation resistance of mullite/yttrium silicate multilayer coatings on C/SiC composites

Long-time oxidation behavior of the nearly stoichiometric polycrystalline SiC fibers under air atmosphere at different temperatures

Oxidation resistance and thermal shock behavior of tri-layer Si/Si–Yb2SiO5/Yb2SiO5–SiC environmental barrier coatings at 1300 °C

Thermal Protection and Dielectric Properties of Borosilicate Coatings for SiCf/SiC Composites Under High-Temperature Oxidation

Oxidation and mechanical properties of SiC fibers after high temperature exposure in air and steam

Properties evolution and damage mechanism of SiC/SiC composites after thermal shock at 1300 °C

Long-term oxidation and ablation behavior of C<sub>f</sub>/ZrB<sub>2</sub>-SiC composites at 1500, 2000, and 2200C

Mechanical properties and microstructure evolution of KD‐SA SiCf/BN/SiC CMCs oxidized at different temperatures

High-temperature tensile behavior of 3D SiC/SiC composites