Abstract:The effect of small amounts of copper oxide, manganese oxide, and stainless steel as sintering additives on the sintering behavior and mechanical properties of Alumina Toughened Zirconia (ATZ, 3Y-TZP with 20 wt% Al2O3) ceramic composites were evaluated and contrasted with that of undoped ATZ by using microwave sintering (MW) method. Green bodies were sintered at 1250°C, 1350°C, and 1500°C using a holding time of 5 min., with a heating rate of 30°C /min. In general, all ATZ samples exhibited a similar trend, as the results showed that the relative density and mechanical properties increased with increasing sintering temperature regardless of the addition of dopants. It was found that the addition of 0.2 wt% CuO, 0.5 wt% MnO2, and 0.2 wt% SS were beneficial in enhancing the densification and improving the mechanical properties of ATZ without inducing grain coarsening. The ATZ composite samples' relative density, tetragonal phase stability, microstructural evolution, Vickers hardness, and fracture toughness were revealed. The addition of 0.2 wt% CuO was the most beneficial in improving the properties of ATZ at a low sintering temperature of 1250°C since the sample obtained the highest relative density of 97%, Vickers hardness of 13.2GPa and fracture toughness of 6.5 MPa m1/2. In contrast, the undoped ATZ required a high sintering temperature to achieve comparable results to the doped samples. The ANOVA analysis revealed that the CuO-doped ATZ sample exhibited the highest significance and was the most suitable in improving both hardness (H) and fracture toughness (KIc) across all temperature conditions. This study also proved that the microwave sintering technique promotes the densification and mechanical properties of ceramic composites compared to the conventional sintering technique.

The Effect of Nano-Al<sub>2</sub>O<sub>3</sub> on Sintering Behavior and Mechanical Property of ZrO<sub>2</sub> Ceramics

The Effect of Nano-Al2O3 on Sintering Behavior and Mechanical Property of ZrO2 Ceramics

Coated-ZrO2 Toughening Al2O3 Matrix Ceramics

Effects of ZrB2 on Mechanical Properties of Al2O3-ZrB2-SiC Composite Ceramics at Room Temperature

Effect of MgO addition on properties of reaction-sintered ZrO2-toughened Al2O3 multiphase ceramic

Effects of Sr2Nb2O7 additive on microstructure and mechanical properties of 3Y–TZP/Al2O3 ceramics

TOUGHENING AND STRENGTHENING OF Al_2O_3 CERAMICS THROUGH NANO-Al_2O_3 ADDITION

Effect of zirconia sol on the microstructure and properties of Al2O3-based ceramic fabricated from natural bauxite

The influence of zirconium dioxide nanoadditives on the properties of mullite-corundum

Effect of Zr2Al4C5 Content on the Mechanical Properties and Oxidation Behavior of ZrB2-SiC-Zr2Al4C5 Ceramics

Effects of Zircon Additive on the Properties of 95-Alumina Ceramic

Microstructure and Mechanical Properties of Hot-Pressed Al2O3–mullite–ZrO2–SiC Composites

Microstructure and phase transformation behavior of Al2O3–ZrO2 under microwave sintering

Effect of MgO Content on the Microstructure and Properties of Zirconia-Toughened Alumina (ZTA) Ceramics by Hot Pressure Sintering10508-3010 M

The influence of ZrO2 on the microstructure and mechanical properties of Al2TiO5 flexible ceramics

Effect of sintering additives on the properties of alumina toughened zirconia (ATZ)

Strengthening of porous Al2O3 ceramics through nanoparticle addition

Effects of ZrO2 ceramics doped with varying content on the mechanical properties and energy release characteristics of W-Zr alloys

Effects of ZrC content on the microstructure and mechanical property of ZrC/ZTA composites consolidated by hot pressing

Effect of Dy2O3 content on microstructure and mechanical properties of zirconia-toughened alumina

Sintering Behavior and Mechanical Properties of Alumina-Coated Zirconia Ceramics