Abstract:Body-centered cubic (BCC) refractory high-entropy alloys (RHEAs) possess the typical advantage of high strength. However, RHEAs often exhibit apparent brittleness at room temperature, which remains great challenges for their engineering applications. In this study, NbMoTaW with 0 and 1 wt% m-ZrO 2 nano-sized ceramic particles RHEAs have been successfully fabricated by ball milling and spark plasma sintering (SPS). The effect of m-ZrO 2 ceramic particles on the microstructures and mechanical properties of NbMoTaW RHEAs was investigated. Results show that the matrix of alloys was characterized by single-phase BCC. Microstructural analysis shows that the grains in the single-phase BCC alloy have been refined by 39.0% through introduction of oxide nano-ceramic particles. The m-ZrO 2 ceramic addition could effectively enhance both the hardness and strength of the NbMoTaW RHEA, accompanied by a slight decrease in plasticity. Compared with the vacuum arc-melting (VAM) method, the sintered NbMoTaW-1ZrO 2 RHEA shows a significant increase in comprehensive compressive properties, especially the ductility. The yield strength, ultimate compressive strength and fracture strain of sintered NbMoTaW-1ZrO 2 RHEA are 1775 MPa, 2118 MPa and 12.4%, respectively, surprisingly increased by 67.8%, 74.9% and 376.9%. A quantitative yield strength model correlating m-ZrO 2 ceramic particle size, volume fraction and NbMoTaW-1ZrO 2 grain size was built. The addition of fine m-ZrO 2 ceramic resulted in Orowan strengthening and fine grains, thereby increasing yield strength of alloy. The superior combination of mechanical properties of the NbMoTaW-1ZrO 2 RHEA could promote it to be a promising alloy in engineering applications.

Coated-ZrO2 Toughening Al2O3 Matrix Ceramics

Activating Continuous Dislocation Pinning Enhanced Toughness of Nanocomposite Coating Through Specially Oriented Semicoherent Heterointerface Lattice Distortion

The Effect of Nano-Al<sub>2</sub>O<sub>3</sub> on Sintering Behavior and Mechanical Property of ZrO<sub>2</sub> Ceramics

The Effect of Nano-Al2O3 on Sintering Behavior and Mechanical Property of ZrO2 Ceramics

Microstructure and mechanical properties of dense ZTA ceramics with high Cr2O3 solution

Ultra-toughened Al2O3–TiC–Co ceramic

The influence of ZrO2 on the microstructure and mechanical properties of Al2TiO5 flexible ceramics

Enhancing the toughness of nano-composite coating for light alloys by the plastic phase transformation of zirconia

Effects of Sr2Nb2O7 additive on microstructure and mechanical properties of 3Y–TZP/Al2O3 ceramics

Effect of MgO addition on properties of reaction-sintered ZrO2-toughened Al2O3 multiphase ceramic

Effects of ZrC content on the microstructure and mechanical property of ZrC/ZTA composites consolidated by hot pressing

TOUGHENING AND STRENGTHENING OF Al_2O_3 CERAMICS THROUGH NANO-Al_2O_3 ADDITION

ZrSiO4 toughed Al2O3 ceramics prepared by reaction sintering

The influence of zirconium dioxide nanoadditives on the properties of mullite-corundum

Mechanical properties and strengthening mechanism of the nano-sized m-ZrO 2 ceramic particle reinforced NbMoTaW refractory high-entropy alloy

ZrO 2 Matrix Toughened Ceramic Material‐Strength and Toughness

Effect of Dy2O3 content on microstructure and mechanical properties of zirconia-toughened alumina

The Effect of Al2O3 on the Thermal Stability and Mechanical Properties of 3Y-TZP

Microstructure and mechanical properties of Zr3Al3C5-based ceramics synthesized by Al-Si melt infiltration

Effects of Residual Stresses on Strength and Crack Resistance in ZrO2 Ceramics with Alumina Coating

ZrO2 Matrix Toughened Ceramic Material‐Strength and Toughness