Abstract:The effect of small amounts of copper oxide, manganese oxide, and stainless steel as sintering additives on the sintering behavior and mechanical properties of Alumina Toughened Zirconia (ATZ, 3Y-TZP with 20 wt% Al2O3) ceramic composites were evaluated and contrasted with that of undoped ATZ by using microwave sintering (MW) method. Green bodies were sintered at 1250°C, 1350°C, and 1500°C using a holding time of 5 min., with a heating rate of 30°C /min. In general, all ATZ samples exhibited a similar trend, as the results showed that the relative density and mechanical properties increased with increasing sintering temperature regardless of the addition of dopants. It was found that the addition of 0.2 wt% CuO, 0.5 wt% MnO2, and 0.2 wt% SS were beneficial in enhancing the densification and improving the mechanical properties of ATZ without inducing grain coarsening. The ATZ composite samples' relative density, tetragonal phase stability, microstructural evolution, Vickers hardness, and fracture toughness were revealed. The addition of 0.2 wt% CuO was the most beneficial in improving the properties of ATZ at a low sintering temperature of 1250°C since the sample obtained the highest relative density of 97%, Vickers hardness of 13.2GPa and fracture toughness of 6.5 MPa m1/2. In contrast, the undoped ATZ required a high sintering temperature to achieve comparable results to the doped samples. The ANOVA analysis revealed that the CuO-doped ATZ sample exhibited the highest significance and was the most suitable in improving both hardness (H) and fracture toughness (KIc) across all temperature conditions. This study also proved that the microwave sintering technique promotes the densification and mechanical properties of ceramic composites compared to the conventional sintering technique.

Effect of MgO Content on the Microstructure and Properties of Zirconia-Toughened Alumina (ZTA) Ceramics by Hot Pressure Sintering10508-3010 M

Effect of MgO addition on properties of reaction-sintered ZrO2-toughened Al2O3 multiphase ceramic

Effect of Dy2O3 content on microstructure and mechanical properties of zirconia-toughened alumina

Effects of ZrC content on the microstructure and mechanical property of ZrC/ZTA composites consolidated by hot pressing

ZrSiO4 toughed Al2O3 ceramics prepared by reaction sintering

Effect of Al2O3 + 4sio2 Additives on Sintering Behavior and Thermal Shock Resistance of MgO-Based Ceramics

Microstructure and Mechanical Properties of ZTA Composites Fabricated by Oscillatory Pressure Sintering

Microstructure and Mechanical Properties of Hot-Pressed Al2O3–mullite–ZrO2–SiC Composites

Effects of Zircon Additive on the Properties of 95-Alumina Ceramic

The Effect of Nano-Al<sub>2</sub>O<sub>3</sub> on Sintering Behavior and Mechanical Property of ZrO<sub>2</sub> Ceramics

Microstructure and mechanical properties of dense ZTA ceramics with high Cr2O3 solution

Effect of AlO + 4SiO Additives on Sintering Behavior and Thermal Shock Resistance of MgO-Based Ceramics

Optimization of microstructure and mechanical properties of oscillatory pressure sintered ZrO<sub>2</sub>-Al<sub>2</sub>O<sub>3</sub>-SiCp ceramics

Sintering mechanism and properties of MgAl2O4–CaAl12O19 composites with ZnO addition

Mechanical properties and wear behaviors of Cu-doped zirconia-toughened alumina ceramics

The Effect of Nano-Al2O3 on Sintering Behavior and Mechanical Property of ZrO2 Ceramics

Microstructure, mechanical properties, friction and wear performance, and cytotoxicity of additively manufactured zirconia-toughened alumina for dental applications

Effect of Al2O3 and TiO2 Addition Amount on Properties of MgO-based Ceramics by Coprecipitation Method

Effect of sintering additives on the properties of alumina toughened zirconia (ATZ)

Optimization of microstructure and mechanical properties of oscillatory pressure sintered ZrO2–Al2O3-SiCp ceramics

Effects of Sr2Nb2O7 additive on microstructure and mechanical properties of 3Y–TZP/Al2O3 ceramics