Abstract:The effect of small amounts of copper oxide, manganese oxide, and stainless steel as sintering additives on the sintering behavior and mechanical properties of Alumina Toughened Zirconia (ATZ, 3Y-TZP with 20 wt% Al2O3) ceramic composites were evaluated and contrasted with that of undoped ATZ by using microwave sintering (MW) method. Green bodies were sintered at 1250°C, 1350°C, and 1500°C using a holding time of 5 min., with a heating rate of 30°C /min. In general, all ATZ samples exhibited a similar trend, as the results showed that the relative density and mechanical properties increased with increasing sintering temperature regardless of the addition of dopants. It was found that the addition of 0.2 wt% CuO, 0.5 wt% MnO2, and 0.2 wt% SS were beneficial in enhancing the densification and improving the mechanical properties of ATZ without inducing grain coarsening. The ATZ composite samples' relative density, tetragonal phase stability, microstructural evolution, Vickers hardness, and fracture toughness were revealed. The addition of 0.2 wt% CuO was the most beneficial in improving the properties of ATZ at a low sintering temperature of 1250°C since the sample obtained the highest relative density of 97%, Vickers hardness of 13.2GPa and fracture toughness of 6.5 MPa m1/2. In contrast, the undoped ATZ required a high sintering temperature to achieve comparable results to the doped samples. The ANOVA analysis revealed that the CuO-doped ATZ sample exhibited the highest significance and was the most suitable in improving both hardness (H) and fracture toughness (KIc) across all temperature conditions. This study also proved that the microwave sintering technique promotes the densification and mechanical properties of ceramic composites compared to the conventional sintering technique.

Effects of Zircon Additive on the Properties of 95-Alumina Ceramic

Effect of MgO addition on properties of reaction-sintered ZrO2-toughened Al2O3 multiphase ceramic

The Effect of the Additive to the Thermal Shock Resistance of Zirconia

Effect of sintering aids on mechanical properties and microstructure of alumina ceramic via stereolithography

ZrSiO4 toughed Al2O3 ceramics prepared by reaction sintering

Effect of zirconia sol on the microstructure and properties of Al2O3-based ceramic fabricated from natural bauxite

Effects of Sr2Nb2O7 additive on microstructure and mechanical properties of 3Y–TZP/Al2O3 ceramics

Sintering Behavior and Mechanical Properties of Alumina-Coated Zirconia Ceramics

Effects of ZrB2 on Mechanical Properties of Al2O3-ZrB2-SiC Composite Ceramics at Room Temperature

The Effect of Nano-Al2O3 on Sintering Behavior and Mechanical Property of ZrO2 Ceramics

The Effect of Nano-Al<sub>2</sub>O<sub>3</sub> on Sintering Behavior and Mechanical Property of ZrO<sub>2</sub> Ceramics

Effect of MgO Content on the Microstructure and Properties of Zirconia-Toughened Alumina (ZTA) Ceramics by Hot Pressure Sintering10508-3010 M

Effect of Zr2Al4C5 Content on the Mechanical Properties and Oxidation Behavior of ZrB2-SiC-Zr2Al4C5 Ceramics

Initial sintering mechanism and additive effect in zirconia ceramics

The Effect of Al2O3 on the Thermal Stability and Mechanical Properties of 3Y-TZP

Effects of Composite Sintering Additives: Al(OH)3+Y2O3+CaF2 on the Performance of Porous Mullite Oxide-Bonded SiC Ceramics

Effect of sintering additives on the properties of alumina toughened zirconia (ATZ)

Reaction mechanisms and properties of in situ porous Al2O3-ZrO2-mullite composites

Low sintering shrinkage and high strength of porous mullite–zirconia ceramics: Effect of AlF3 and ZrSi2 contents

Effects of added aluminum chromium slag on the structure and mechanical properties of colored zirconia ceramics

Effects of ZrC content on the microstructure and mechanical property of ZrC/ZTA composites consolidated by hot pressing