Abstract:Passivating contact solar cells have gradually become the mainstream cell technology due to their excellent performance, and further improving the conversion efficiency has become a focus of subsequent research. Typically, achieving excellent field-effect passivation and low contact resistivity in doped polycrystalline silicon (poly-Si) solar cells requires heavy phosphorus doping. However, this approach can lead to a predicament where excessive phosphorus diffuses into the Si substrate during annealing, causing recombination losses. To address this challenge, a tandem passivation contact structure incorporating an intrinsic amorphous silicon (a-Si ( i)) film within the passivation layers is introduced to retard the diffusion of phosphorus into the Si substrate. Comprehensive characterizations of the tandem structure were carried out to delve into the underlying mechanisms of films with the integrated a-Si ( i) layer, including simulations, surface microscopy, active dopants profiling, crystallographic structure, chemical bonding, elemental distribution, and electrical properties. Simulations revealed that the inserted intrinsic layer effectively counteracts the clustering of phosphorus atoms, leading to a more even distribution during crystal growth. Furthermore, active dopant profiles indicate the potential of the introduced a-Si ( i) layer to tailor the in-diffused dopant profile. Microscopy investigations revealed the occurrence of blistering when the a-Si ( i) thickness exceeds 30 nm. Passivation and contact performances of TOPCon solar cells were assessed as the a-Si ( i) thickness was varied. Notably, optimal electrical properties were achieved with 20 nm a-Si ( i) thickness. At this thickness, the implied open-circuit voltage ( iV) of the hydrogenated lifetime sample was promoted to more than 736.6 mV on the polished wafer, corresponding to the lowest single-side saturation current density ( J) of 4.3 fA/cm . In addition, a low contact resistivity of 1.4 mΩ·cm was achieved. Based on this tandem passivation contact structure, industrial-sized TOPCon solar cells were fabricated, giving an average efficiency of 23.83%, 0.25% higher than that of the baseline counterparts on the production line. The above results demonstrate the role of the a-Si ( i) film as a buffer layer, retarding the diffusion of phosphorus into the Si substrate and obtaining a better passivation effect. This enables us to further tailor the doping profile for high-efficiency solar cells. Our work thus highlights a promising strategy to improve the performance of TOPCon solar cells and showcases its potential for implementation in industrial manufacturing.

Application of Phosphorus‐Doped Polysilicon‐Based Full‐Area Passivating Contact on the Front Textured Surface of P‐type Silicon

Tuning of the Contact Properties for High-Efficiency Si/PEDOT:PSS Heterojunction Solar Cells

Phosphorus-doped polycrystalline silicon passivating contacts via spin-on doping

High-efficiency N-Type Silicon PERT Bifacial Solar Cells with Selective Emitters and Poly-Si Based Passivating Contacts

Ga-doped Czochralski silicon with rear p-type polysilicon passivating contact for high-efficiency p-type solar cells

Current status and challenges for hole-selective poly-silicon based passivating contacts

Phosphorus-diffused polysilicon contacts for solar cells

Passivated Emitter and Rear Cell Silicon Solar Cells with a Front Polysilicon Passivating Contacted Selective Emitter

The Passivation Characteristics of Poly-Si/SiOx Stack for High-Efficiency Silicon Solar Cells

Solution-Doped Polysilicon Passivating Contacts for Silicon Solar Cells

Large-area bifacial n-TOPCon solar cells with in situ phosphorus-doped LPCVD poly-Si passivating contacts

Impurity Gettering by Boron‐ and Phosphorus‐Doped Polysilicon Passivating Contacts for High‐Efficiency Multicrystalline Silicon Solar Cells

Application of SiO2 Passivation Technique in Mass Production of Silicon Solar Cells

Poly-Si passivating contacts prepared via phosphorus spin-on-doping: A comparison between different silicon deposition methods

Quantitative Understanding and Implementation of Screen Printed p+ Poly-Si/Oxide Passivated Contact to Enhance the Efficiency of p-PERC Cells

Application of n‐Polysilicon Rear Emitter for High‐Efficiency p‐TOPCon Solar Cells

SiOx/polysilicon selective emitter prepared by PECVD-deposited amorphous silicon plus one-step firing enabling excellent J0,met of < 235 fA/cm2 and ρc of < 2 mΩ·cm2

Progress and Future Prospects of Wide‐Bandgap Metal‐Compound‐Based Passivating Contacts for Silicon Solar Cells

Performance of Large Area n-TOPCon Solar Cells with Selective Poly-Si Based Passivating Contacts Prepared by PECVD Method

Novel Tandem Passivated Contact Approach for High-Efficiency Industrial TOPCon Solar Cells

Numerical study of mono-crystalline silicon solar cells with passivated emitter and rear contact configuration for the efficiency beyond 24% based on mass production technology