Abstract:The hole defects can easily occur in magnesium alloy castings that are prepared by low pressure lost foam casting (LP-LFC) process when the process parameters such as vacuum, pouring temperature and filling velocity are not properly selected. In this study, the forming mechanism of the hole defects in AZ91D magnesium castings by LP-LFC process was investigated. The shape, location and surface appearance of the hole defects were observed using optical microscopy and scanning electron microscopy, and the chemical composition on the surface of the holes was analyzed using energy spectrometer. The result indicates that there are two types of hole defects, i.e., the pyrolysis products related hole defects, including concentrative hole and blow hole defects, and slag related hole defects. The concentrative hole and the blow-hole defects were formed either by the liquid-EPS degradation products entrapped in the molten metal under the condition that the pouring temperature is equal to or lower than 730 ℃, or by the hindered transport of EPS pyrolysis products. Some irregular shape hole defects were caused by slag or by coating slough entrapment when the pouring temperature is equal to 750 ℃ and the filling velocity is equal to or greater than 100 mm·s-1. To reduce or eliminate the hole defects, the vacuum and filling velocity must be properly chosen to ensure that the metal front profile exhibits convex shape and in laminar current state, and the pouring temperature should be just high enough to ensure that the molten melt has adequate heat energy to complete the foam pyrolysis and to fully occupy the mould. For AZ91D magnesium castings in this study, the parameters should be 730 ℃ pouring temperature, 0.02-0.03 MPa vacuum and 80 mm·s-1 filling velocity.

Microstructure And Mechanical Properties Of Magnesium Alloy Prepared By Lost Foam Casting

Study on Structure and Corrosion Resistance of AZ91 Magnesium Alloy in Lost Foam Casting Process

Microstructures and Mechanical Properties Ofaz91d Magnesium Alloy Processed by Low Pressure Die Casting

Research on Structure Property of AZ91D Magnesium Alloy Produced by Liquid Combination Process of Die Casting and Forging

Microstructure and Properties of AZ91D Magnesium Alloy in Combination Process of Die Casting with Forging

Effect of Aluminium Content and Processing Parameters on the Microstructure and Mechanical Properties of Laser Powder-Bed Fused Magnesium-Aluminium (0, 3, 6, 9wt%) Powder Mixture

Research on Microstructures Modification of AZ91 Mg Alloy Based on Lost Foam Casting

Study on Typical Hole Defects in Az91d Magnesium Alloy Prepared by Low Pressure Lost Foam Casting

INFLUENCE OF SOLUTION AND AGING ON MECHANICAL PROPERTIES OF AZ91HP DIE-CASTING ALLOY

Mechanical Properties and Microstructures of Mg-Al-Zn Alloys with High Aluminum Contents

Microstructure Evolution and Mechanical Properties of Rheo-Squeeze Casting AZ91-Ca Alloy During Heat Treatment

Effect of Pouring Temperature During a Novel Solid–liquid Compound Casting Process on Microstructure and Mechanical Properties of AZ91D Magnesium Alloy Parts with Arc-Sprayed Aluminum Coatings

Study on the Cavity Defects of Low-Pressure Lost Foam Casting for Magnesium Alloy

Research on the Comparison of the Macroscopic Defect and the Mechanical Property of AZ91D Magnesium Alloy Parts Produced by Liquid Combination Process of Die Casting and Forging and Liquid Die Casting

Preparation of Al2O3/AZ91D Mg Interpenetrating Composites Using Lost Foam Casting Combined with Layered Extrusion Forming

Selective laser melted AZ91D magnesium alloy with superior balance of strength and ductility

Study on Mechanical Properties of Vacuum Die-cast AZ91D Magnesium Alloy

Semi-solid Slurry Preparation, Rheo-Die Casting and Rheo-Squeeze Casting of an AZ91–2Ca–1.5Ce Ignition-Proof Magnesium Alloy by Gas-Bubbling Process

Microstructures and Mechanical Properties of High Strength AZ91 Mg Alloy by Spray Forming Technology

Investigation of Properties in Magnesium Alloy Thin Plates after Die Casting Processes

Heat-Treatment Characteristics and Structure-Property Relationships of Thixomolded AZ91 and Ultralight LAZ771 Magnesium Alloys