Abstract:Highlights • A special-shaped C sf /AZ91D composite part with a high fiber volume fraction of 23.0% was firstly prepared by the LSEVI process. • The desired configuration features were directly formed, in the way of near-net forming. • The excellent microstructure with sufficient infiltration and no fiber aggregation was obtained. • Compared with the AZ91D, the compressive strength of the composite part was effectively increased by ∼40%. To meet the increased demand for light-weight and high-performance special-shaped load bearing parts in automotive industry, the short carbon fiber reinforced magnesium matrix composite (C sf /Mg) part with complex configuration features and abrupt cross-sectional transitions was fabricated by liquid-solid extrusion following vacuum pressure infiltration process (LSEVI). Near-net forming schemes of both the special-shaped fiber preform and composite part were proposed. The effect of process parameters on the forming quality of the composite part was discussed. Meanwhile, the microstructures and compressive properties in different regions of the part were analyzed. The results show that the forward forming scheme provides the special-shaped fiber preform with no surface defects. For the C sf /AZ91D part, its internal microstructures show that the infiltration of liquid magnesium is sufficient and uniform. The compressive strength of the composite part can reach up to 487 MPa, corresponding to ∼40% increase compared to 335 MPa of the AZ91D alloy. The average compressive strain of composites is less than 10%, which is about 50% of that of the AZ91D alloy. When the fiber orientation is parallel to the shear direction on the shear plane, the load-bearing capacity of the fiber is much higher than that of the fiber perpendicular to the shear direction. This work not only provides a convenient approach to fabricate special-shaped preform with high fiber volume fraction, but also gives a demonstration for the near-net forming of C sf /Mg parts with excellent material isotropy and compressive properties. Graphical abstract Download : Download high-res image (275KB) Download : Download full-size image

Preparation of Al2O3/AZ91D Mg Interpenetrating Composites Using Lost Foam Casting Combined with Layered Extrusion Forming

Effective Control of Microstructure Evolution in AZ91D Magnesium Alloy by SiC Nanoparticles in Laser Powder-Bed Fusion

Micro-arc Oxidation Behaviors of AZ91D Magnesium Alloy in Different Electrolytes

Effect of Aluminium Content and Processing Parameters on the Microstructure and Mechanical Properties of Laser Powder-Bed Fused Magnesium-Aluminium (0, 3, 6, 9wt%) Powder Mixture

Interfacial research on interpenetrating network structure ZrO2/Al-Mg composites prepared by Extrusion Freeform Fabrication 3DP and pressureless infiltration

Preparation of the high compressive performance special-shaped C sf /AZ91D composite part using the liquid-solid extrusion following vacuum pressure infiltration process

Development of AZ91D Magnesium Alloy-Graphene Nanoplatelets Composites Using Thixomolding Process

Surface pre-oxidation for enhancing laser assisted joining between carbon fiber reinforced thermoplastic composites and AZ31B Mg alloy

Composition design method of Al-Cu alloy for laser powder bed fusion

Al2O3 eliminating defects in the Al coating by laser cladding to improve corrosion and wear resistance of Mg alloy

Formation of Mg–Al LDHs coating by hydrothermal treatment on laser remelting pretreated AZ31 magnesium alloy for enhanced corrosion resistance

In Situ Preparation of Mg-Al-Co Layered Double Hydroxides on Microarc Oxidation Ceramic Coating of LA103Z Magnesium-Lithium Alloy for Enhanced Corrosion Resistance

Hybrid Filler Actions on Functional Performance Evaluation of Magnesium Alloy (AZ61) Hybrid Nanocomposites

Microstructure evolution and mechanical properties strengthening in laser powder bed fusion of high-strength SiC and TiB 2 co-reinforced Al-Zn-Mg-Cu composites

Effect of MgO particles with in-situ graphene coating on mechanical and thermal expansion properties of aluminum matrix composites

Study on the Cavity Defects of Low-Pressure Lost Foam Casting for Magnesium Alloy

An Al-Al interpenetrating-phase composite by 3D printing and hot extrusion

Corrosion resistance study of ZIF-67/Co-Fe LDHs composite coating on the surface of AZ31 magnesium alloy micro-arc oxidation film

Mg/ZrO2 Metal Matrix Nanocomposites Fabricated by Friction Stir Processing: Microstructure, Mechanical Properties, and Corrosion Behavior

Study on Typical Hole Defects in Az91d Magnesium Alloy Prepared by Low Pressure Lost Foam Casting

Study on Corrosion Characteristics and Mechanism of Laser Powder Bed Fusion of Mg-Zn-Zr Alloy