Abstract:Because of their low density, high strength-to-weight ratio and high damping capacity, magnesium alloys have gained increasing applications in many fields, especially for die-cast magnesium alloys. The application of die-cast magnesium alloys in structures and repair welding of casting defects necessitates the development of welding techniques. As a high energy density thermal source, laser welding can reduce many welding defects compared with conventional welding methods, but pore formation during welding of die-cast magnesium alloys is still a severe problem that has not been solved. This paper seeks to identify the mechanism of pore formation during laser welding of die-cast magensium alloys and search for a metallurgic solution of porosity. The great tendency to pore formation in die-cast magnesium alloys is attributed to high gas content in the base metal. The characteristic of gas source in die-cast magnesium alloys and the process of pore formation during laser welding are studied by some experiments including analysis of characteristic parameters of pores (porosity, average diameter and number densities), change of densities before and after heating (350 degrees C, holding time 1 h) and pore formation tendency under different vacuo heating conditions (heating the base metal to 350 degrees C under vacuum environment of different holding time). The results show that heating increases porosity, average diameter and number densities, which lead to the reduction of bulk density. Vacuo heating before welding can reduce porosity to a great extent, and with holding time prolonging, porosity reduces. In die casting, there are molecular hydrogen and atomic hydrogen in die-cast magnesium alloys. The hydrogen gas (molecular hydrogen) in high pressure pores in the base metal expands sharply in the molten pool, and the oversaturated atomic hydrogen can also form new pores or contribute to the growth of exsisting pores. That is to say that both molecular hydrogen and atomic hydrogen contribute to the pore formation of die-cast magnesium alloys during laser welding. During vacuo heating before welding, atomic hydrogen can escape in part through diffusion, thus reducing the tendency to form pores. With holding time of vacuo heating prolonging, the amount of atomic hydrogen escaping from the base metal increases, thus porosity reduces. Adding elements, which can combine hydrogen to form hydride, may be a possible solution to pore formation in die-cast magnesium alloys. Preliminary experiments show that adding Zr to welds during welding can reduce the tendency to form pores obviously, the reason for this needs further research.

Study on the Cavity Defects of Low-Pressure Lost Foam Casting for Magnesium Alloy

Study on Typical Hole Defects in Az91d Magnesium Alloy Prepared by Low Pressure Lost Foam Casting

Effect of Vacuum Degree on Quality of Magnesium Alloy by Low-Pressure Expendable Pattern Casting

Determination of Optimal Temperature for Defect-Free Casting of Aluminium in the LP-LFC Process

Analysis of Formation Mechanism of Typical Defects in Aluminum (Magnesium) Alloys Castings by the Expendable Pattern Shell Casting with Vacuum and Low Pressure

Mass Transfer of Lost Foam Casting and Its Influence on the Casting Quality

Prediction method of shrinkage cavity and shrinkage porosity in solidification process under low-pressure casting

Accurate Detection and Analysis of Pore Defects in Laser Powder Bed Fusion WE43 Magnesium Alloys

Determination of casting parameters of thick wall die-casting of magnesium alloy and simulation of its processing

EXPERIMENTAL STUDY ON THE REASON OF PORE FORMATION IN LASER WELDING OF DIE-CAST MAGNESIUM ALLOY

Investigation of Microstructures and Mechanical Properties of A356 Aluminum Alloy Produced by Expendable Pattern Shell Casting Process with Vacuum and Low Pressure

Low-pressure die casting of magnesium alloy AM50: Response to process parameters

Corrosion Behaviour of Laser Powder Bed Fused Bulk Pure Magnesium in Hank's Solution

Processing Parameters of LFC Shell Mold Casting Aluminum Alloy Castings with Vacuum and Low Pressure

Comparison of Microstructures and Properties of Aluminum Alloy Between Expendable Pattern Shell Casting with Vacuum and Low-Pressure and Lost Foam Casting

Experimental Study on Pores in Laser Welding of Magnesium Alloys

Preparation of Al2O3/AZ91D Mg Interpenetrating Composites Using Lost Foam Casting Combined with Layered Extrusion Forming

Effect of Aluminium Content and Processing Parameters on the Microstructure and Mechanical Properties of Laser Powder-Bed Fused Magnesium-Aluminium (0, 3, 6, 9wt%) Powder Mixture

Formation Mechanism of Surface Crack in Low Pressure Casting of A360 Alloy

Correlation of Microstructure with Mechanical Properties and Fracture Behavior of A356-T6 Aluminum Alloy Fabricated by Expendable Pattern Shell Casting with Vacuum and Low-Pressure, Gravity Casting and Lost Foam Casting

Study on Corrosion Characteristics and Mechanism of Laser Powder Bed Fusion of Mg-Zn-Zr Alloy