Abstract:In this study, a new casing process named expendable pattern shell casting process with vacuum and low pressure (EPSC-VL) was introduced to produce complicated and thin-walled aluminum alloy castings. The gas flowrate is one of the most important process parameters for manufacturing castings during the EPSC-VL process. In the present work, the influence of gas flowrate on the filling ability and internal quality of A356 aluminum alloy castings fabricated by the EPSC-VL process were investigated. Moreover, the filling ability, internal quality, as well as mechanical properties of A356 aluminum alloy castings obtained by EPSC-VL and lost foam casting (LFC) processes were also compared. The results obtained suggested that the filling length increased with the increase of gas flowrate, and the filling length of the thick section was larger than that of the thin section under the same gas flowrate when the gas flowrate was less than 19 m(3)/h. Furthermore, the porosity of castings decreased with increasing gas flowrate, and the microstructure of castings became denser, and the internal quality of castings was obviously improved. The comparison experiments showed that the EPSC-VL process had superior filling ability, internal quality, and mechanical properties compared with the LFC process, and the surface quality of castings obtained by EPSC-VL process was also better than that of the LFC process. The casting practice of complicated and thin-walled A356 aluminum alloy intake manifold part also suggested that the EPSC-VL process had an obvious advantage for the fabrication of complicated and thin-walled aluminum alloy castings compared with the LFC process.

Comparison of Microstructures and Properties of Aluminum Alloy Between Expendable Pattern Shell Casting with Vacuum and Low-Pressure and Lost Foam Casting

Investigation of Microstructures and Mechanical Properties of A356 Aluminum Alloy Produced by Expendable Pattern Shell Casting Process with Vacuum and Low Pressure

Correlation of Microstructure with Mechanical Properties and Fracture Behavior of A356-T6 Aluminum Alloy Fabricated by Expendable Pattern Shell Casting with Vacuum and Low-Pressure, Gravity Casting and Lost Foam Casting

Microstructure, Tensile Properties and Fractography of A356 Alloy under As-Cast and T6 Obtained with Expendable Pattern Shell Casting Process

Tensile properties and fractography of A356 alloy produced by EPSC-VL process

Influence of Gas Flowrate on Filling Ability and Internal Quality of A356 Aluminum Alloy Castings Fabricated Using the Expendable Pattern Shell Casting with Vacuum and Low Pressure

Influence of Process Parameters on Filling Ability of A356 Aluminium Alloy in Expendable Pattern Shell Casting with Vacuum and Low Pressure

Effects of Process Parameters on Internal Quality of Castings During Novel Casting

Comparison on the Electrochemical Corrosion Behavior of Ti6Al4V Alloys Fabricated by Laser Powder Bed Fusion and Casting

Experimental Studies on Rheocasting Processing of A356 Alloy

Effect of Different Casting Techniques on the Microstructure and Mechanical Properties of AE44-2 Magnesium Alloy

Comparing microstructure and mechanical properties of AlSi10 alloy produced by powder bed fusion-laser beam and high pressure die casting

An Experimental Investigation of the Material Properties of the A356 Aluminum Alloy Power Fittings in the Vacuum Die-Casting Process

Comparison of Laser Powder Bed Fusion and Cast Inconel 713 Alloy in Terms of Their Microstructure, Mechanical Properties, and Fatigue Life

Optimization of casting means and heat treatment routines for improving mechanical and corrosion resistance properties of A356-0.54Sc casting alloy

Study on the Cavity Defects of Low-Pressure Lost Foam Casting for Magnesium Alloy

The effect of different high pressure die casting parameters on 3D microstructure and mechanical properties of AE44 magnesium alloy

Comparative study on microstructure and electrochemical corrosion resistance of Al7075 alloy prepared by laser additive manufacturing and forging technology

Numerical Simulation of Lost-Foam Casting for Key Components of A356 Aluminum Alloy in New Energy Vehicles

Numerical Simulation and Experimental Investigation of Microstructure Evolution and Flow Behavior in the Rheological Squeeze Casting Process of A356 Alloy

Microstructure and mechanical property of A356 cast remanufactured by ultrasonic frequency pulsed TIG process