Abstract:The Laser Powder Bed Fusion (LPBF) process offers the capacity to produce parts with complicated geometries that cannot be manufactured using traditional manufacturing processes. The aerospace industry is particularly interested in this capability because it may enable the creation of high-temperature structural parts with sophisticated cooling channel layouts. This would allow future gas turbines to operate at higher temperatures, resulting in higher efficiency. However, if they are to realize this promise, they must first enhance their knowledge of the influence of the LPBF process on alloy microstructures and its subsequent effect on mechanical properties. Furthermore, this study offers information on how to comprehend microstructural development and the impact it has on the mechanical characteristics of the CM247LC alloy processed by LPBF. Using the Direct Metal Laser Sintering technique based on Laser Power Bed Fusion, the CM247LC nickel-based superalloy was manufactured. When the CM247LC alloy was examined microscopically, carbides and cracks (both straight and serrated) were found. Electron Backscatter Diffraction studies revealed elongated grains in the longitudinal section and equiaxed clusters in the transverse section. Longitudinal sections have been determined to be predominantly composed of columnar grains with cells that have an average size of 0.7 μm. The γ/γ′ eutectic, as well as highly concentrated precipitates and highly concentrated dislocations, separate these cells from neighboring cells and grains. Up to 10 nm of the γ′ can be found inside the cells, despite having a diameter of up to 40 nm at the cell walls. The calculated rate of cooling during solidification is around 10 6 K/s based on the observed cell diameters. Tensile tests on samples that had just been manufactured reveal that yield strength is comparable to previous studies. High precipitate concentrations, dislocations density, fine cell structure, and γ' inside cells are interpreted as the sources of high strength in as-fabricated conditions.

Comparison of Laser Powder Bed Fusion and Cast Inconel 713 Alloy in Terms of Their Microstructure, Mechanical Properties, and Fatigue Life

Microstructure and mechanical property comparison of Inconel alloys fabricated using micro and conventional laser powder bed fusion

A Review on Laser Powder Bed Fusion of Inconel 625 Nickel-Based Alloy

Microstructural, mechanical and wear behaviour of Inconel-718 produced through laser-powder bed-fused additive manufacturing

Microstructure, Mechanical Property and Heat Treatment Schedule of the Inconel 718 Manufactured by Low and High Power Laser Powder Bed Fusion

Mechanical Behavior of Laser Powder Bed Fusion Processed Inconel 625 Alloy

Effect of Surface Modification on the High Temperature Low Cycle Fatigue Performance of LPBF 316L Austenitic Steel

Effects of Process Parameters and Heat Treatment on Microstructure and Mechanical Characteristics of Laser Powder Bed Fusion Alloy Inconel 718

Creep-fatigue Properties and Deformation Mechanism of 316L Steel Fabricated by Laser Powder Bed Fusion (PBF-LB/M)

Comparative Investigation of Fatigue Properties Between Additively and Conventionally Manufactured Invar 36 Alloy

Tensile and Low‐Cycle Fatigue Behavior of Laser Powder Bed Fused Inconel 718 at Room‐ and High Temperature

The evolution of microstructure and mechanical properties of Inconel 625 alloy fabricated by laser powder bed fusion via novel hybrid scanning strategy

Effects of the microstructure and texture characteristics on mechanical properties of the Al–Ni–Cu–Fe alloy manufactured by laser powder bed fusion

Laser Powder Bed Fusion of Inconel 718 on 316 Stainless Steel

The Precipitation Behavior Effect of Δ and Γ" Phases on Mechanical Properties of Laser Powder Bed Fusion Inconel 718 Alloy

Assessment of mechanical properties and fatigue performance of a selective laser melted nickel-base superalloy Inconel 718

In Situ Alloying of a Modified Inconel 625 via Laser Powder Bed Fusion: Microstructure and Mechanical Properties

Comparing microstructure and mechanical properties of AlSi10 alloy produced by powder bed fusion-laser beam and high pressure die casting

Impact of Laser Power and Scanning Velocity on Microstructure and Mechanical Properties of Inconel 738LC Alloys Fabricated by Laser Powder Bed Fusion

Impact of annealing treatment on the fatigue behavior of Inconel 625 produced by laser‐based powder bed fusion

Structural Characterization and Strength Assessment of Laser Powder Bed Fusion Manufactured CM247LC Nickel Based Super Alloy