Abstract:The Laser Powder Bed Fusion (LPBF) process offers the capacity to produce parts with complicated geometries that cannot be manufactured using traditional manufacturing processes. The aerospace industry is particularly interested in this capability because it may enable the creation of high-temperature structural parts with sophisticated cooling channel layouts. This would allow future gas turbines to operate at higher temperatures, resulting in higher efficiency. However, if they are to realize this promise, they must first enhance their knowledge of the influence of the LPBF process on alloy microstructures and its subsequent effect on mechanical properties. Furthermore, this study offers information on how to comprehend microstructural development and the impact it has on the mechanical characteristics of the CM247LC alloy processed by LPBF. Using the Direct Metal Laser Sintering technique based on Laser Power Bed Fusion, the CM247LC nickel-based superalloy was manufactured. When the CM247LC alloy was examined microscopically, carbides and cracks (both straight and serrated) were found. Electron Backscatter Diffraction studies revealed elongated grains in the longitudinal section and equiaxed clusters in the transverse section. Longitudinal sections have been determined to be predominantly composed of columnar grains with cells that have an average size of 0.7 μm. The γ/γ′ eutectic, as well as highly concentrated precipitates and highly concentrated dislocations, separate these cells from neighboring cells and grains. Up to 10 nm of the γ′ can be found inside the cells, despite having a diameter of up to 40 nm at the cell walls. The calculated rate of cooling during solidification is around 10 6 K/s based on the observed cell diameters. Tensile tests on samples that had just been manufactured reveal that yield strength is comparable to previous studies. High precipitate concentrations, dislocations density, fine cell structure, and γ' inside cells are interpreted as the sources of high strength in as-fabricated conditions.

Mechanical Behavior of Laser Powder Bed Fusion Processed Inconel 625 Alloy

A Review on Laser Powder Bed Fusion of Inconel 625 Nickel-Based Alloy

Heat-Treated Inconel 625 by Laser Powder Bed Fusion: Microstructure, Tensile Properties, and Residual Stress Evolution

Mechanical Characterization of Near-Isotropic Inconel 718 Fabricated by Laser Powder-Bed Fusion

Microstructure and mechanical properties at elevated temperatures of as-built and heat-treated Inconel 718 produced through laser powder bed fusion processes

Structural Characterization and Strength Assessment of Laser Powder Bed Fusion Manufactured CM247LC Nickel Based Super Alloy

Knowledge of process-structure-property relationships to engineer better heat treatments for laser powder bed fusion additive manufactured Inconel 718

Microstructural Development in As Built and Heat Treated IN625 Component Additively Manufactured by Laser Powder Bed Fusion

A review on microstructure, mechanical behavior and post processing of additively manufactured Ni-based superalloys

In Situ Alloying of a Modified Inconel 625 via Laser Powder Bed Fusion: Microstructure and Mechanical Properties

Microstructures and High-Temperature Mechanical Properties of Inconel 718 Superalloy Fabricated via Laser Powder Bed Fusion

Inconel 718 produced by laser powder bed fusion: an overview of the influence of processing parameters on microstructural and mechanical properties

A Review on Additive Manufacturing Processes of Inconel 625

Microstructure and mechanical property comparison of Inconel alloys fabricated using micro and conventional laser powder bed fusion

Microstructures and Mechanical Behaviors of Additive Manufactured Inconel 625 alloys via Selective Laser Melting and Laser Engineered Net Shaping

Milling investigations and yield strength calculations for nickel alloy Inconel 625 manufactured with laser powder bed fusion process

Impact of annealing treatment on the fatigue behavior of Inconel 625 produced by laser‐based powder bed fusion

Mechanical properties of laser powder bed fusion processed Inconel alloy IN718 in different heat treatment conditions through small scale specimen testing

The evolution of microstructure and mechanical properties of Inconel 625 alloy fabricated by laser powder bed fusion via novel hybrid scanning strategy

Effect of Layer Thickness and Heat Treatment on Microstructure and Mechanical Properties of Alloy 625 Manufactured by Electron Beam Powder Bed Fusion

Microstructural, mechanical and wear behaviour of Inconel-718 produced through laser-powder bed-fused additive manufacturing