Abstract:This study presents a detailed investigation into the deformation behaviour and the factors affecting the strength and ductility of laser powder bed fusion (LPBF) Ni-based superalloy 718 (Inconel 718) in both as-printed and heat-treated conditions using in-situ SEM + EBSD. The results show that following post-deposition high homogenization temperatures, the columnar grain structure of the as-printed Inconel 718 alloy successfully transformed to a nearly uniform grain size and the subsequent aging processes facilitated the precipitation of strengthening phases (gamma ', ' , gamma"). The specimen subjected to heat treatment (HT1) exhibited higher strength but lower ductility, while the as-printed specimen shows higher tensile elongation due to high initial dislocation density. In contrast, the heat-treated (HT2) specimen presented a more optimal combination of strength and ductility. The underlying mechanism for the enhanced tensile properties in the HT2 specimen was nearly homogeneous deformation trend across the grains and ultrafine precipitation of hardening phases. In addition, the twin boundaries were stable in the early deformation stages and maintained their orientation. Multiple slip systems were activated at the high-deformation stage, resulting in a high proportion of geometric necessary dislocations. Further, the interaction of deformation-induced dislocation with twin boundaries transformed them into general boundaries such as high and low-angle grain boundaries, ultimately increasing ductility. On contrary, in the HT1 specimen, the deformation inhomogeneity in grains enabled the strain localization at grain boundaries, which ultimately caused the early formation of cracks.

Effect of Layer Thickness and Heat Treatment on Microstructure and Mechanical Properties of Alloy 625 Manufactured by Electron Beam Powder Bed Fusion

Comprehensive and Comparative Heat Treatment of Additively Manufactured Inconel 625 Alloy and Corresponding Microstructures and Mechanical Properties

Effects of Solution Treatments on the Microstructure and Mechanical Properties of Inconel 625 Fabricated by Electron Beam Freeform Fabrication

Effects of Heat Treatments on the Microstructure and Mechanical Properties of Inconel 718 Alloy Fabricated by Electron Beam Freeform Fabrication

Heat-Treated Inconel 625 by Laser Powder Bed Fusion: Microstructure, Tensile Properties, and Residual Stress Evolution

Microstructural Development in As Built and Heat Treated IN625 Component Additively Manufactured by Laser Powder Bed Fusion

Insight into Elongation and Strength Enhancement of Heat-Treated LPBF Ni-based Superalloy 718 Using In-Situ SEM-EBSD

Mechanical Behavior of Laser Powder Bed Fusion Processed Inconel 625 Alloy

Microstructures and High-Temperature Mechanical Properties of Inconel 718 Superalloy Fabricated via Laser Powder Bed Fusion

Effect of heat treatments on the microstructure and mechanical properties of IN738LC prepared by electron beam powder bed fusion

Effect of heat treatment on the microstructure and mechanical properties of Inconel 718 processed by selective laser melting

Microstructure and Microhardness of Electron Beam Melted Ti-6Al-4V Components with Differential Thickness in Initial Deposition Layers

Microstructure and mechanical properties at elevated temperatures of as-built and heat-treated Inconel 718 produced through laser powder bed fusion processes

Effect of Heat Treatment on Microstructure and Mechanical Properties of Inconel 625 Alloy Fabricated by Pulsed Plasma Arc Deposition

Effect of Fe and C Contents on the Microstructure and High-Temperature Mechanical Properties of IN625 Alloy Processed by Laser Powder Bed Fusion

Effects of Process Parameters and Heat Treatment on Microstructure and Mechanical Characteristics of Laser Powder Bed Fusion Alloy Inconel 718

Effect of building direction and heat treatment on mechanical properties of Inconel 939 prepared by additive manufacturing

Microstructural Evolution and Mechanical Properties of Inconel 625 Alloy During Pulsed Plasma Arc Deposition Process

Impact of Laser Power and Scanning Velocity on Microstructure and Mechanical Properties of Inconel 738LC Alloys Fabricated by Laser Powder Bed Fusion

In situ interlayer hot forging arc-based directed energy deposition of Inconel® 625: process development and microstructure effects

Effects of a modified heat-treatment on microstructure and mechanical properties of additively manufactured Inconel 718