Abstract:Products produced by additive manufacturing (AM) seek to exploit net shape manufacturing by eliminating or minimizing post-process stages such as machining. However, many applications which include turbo machinery components with tight dimensional tolerances and a smooth surface finish will require at least a light machine finishing stage. This paper investigates the machinability of the additively fabricated INCONEL718 (IN718) alloy produced by laser melting powder bed fusion (LM-PBF) with different levels of spherical porosity in the microstructure. The literature suggests that the band width for laser energy density, which combines the various scan process parameters to obtain a low spherical type porosity in the LM-PBF IN718 alloy (~1%), has wide breadth. With the increasing laser energy density and above a threshold, there is a rapid increase in the spherical pore size. In this paper, three tube samples each with different levels of spherical porosity were fabricated by varying the laser energy density for LM-PBF of the IN718 alloy within the stable and higher energy density range and the porosity measured. A low laser energy density was avoided due to balling up, which promotes highly irregular lack of fusion defects and poor consolidation within the alloy microstructure. An orthogonal turning test instrumented, with a three-component dynamometer to measure the cutting forces, was performed on AM produced IN718 tube samples under light cut conditions to simulate a finish machining process. The orthogonal turning tests were also performed on a tube sample obtained from the wrought extruded stock. The machining process parameters, which were studied include varying the cutting speed at three levels, at a fixed feed and under dry cut conditions for a short duration to avoid the tool wear. The results obtained were discussed and a notable finding was the higher rate of built-up-edge formation on the tool tip from the AM samples with a higher porosity and especially at a higher cutting speed. The paper also discusses the mechanisms that underpin the findings.

Inconel 718 produced by laser powder bed fusion: an overview of the influence of processing parameters on microstructural and mechanical properties

Impact of process parameters on the dynamic behavior of Inconel 718 fabricated via laser powder bed fusion

Effect of parameters on quality of IN718 parts using laser additive manufacturing

Study on the Effect of Powder-Bed Fusion Process Parameters on the Quality of as-Built IN718 Parts Using Response Surface Methodology

A Review on Laser Powder Bed Fusion of Inconel 625 Nickel-Based Alloy

Effect of post-processing on microstructure and mechanical properties of Alloy 718 fabricated using powder bed fusion additive manufacturing processes

Effects of heat treatment on surface integrity and wear performance of Inconel 718 alloy fabricated by laser powder bed fusion process additive manufacturing under different laser power and scanning speed parameters

Mechanical Behavior of Laser Powder Bed Fusion Processed Inconel 625 Alloy

Microstructure and mechanical property comparison of Inconel alloys fabricated using micro and conventional laser powder bed fusion

Microstructural, mechanical and wear behaviour of Inconel-718 produced through laser-powder bed-fused additive manufacturing

Evaluation of Inconel 718 Metallic Powder to Optimize the Reuse of Powder and to Improve the Performance and Sustainability of the Laser Powder Bed Fusion (LPBF) Process

Machinability of INCONEL718 Alloy with a Porous Microstructure Produced by Laser Melting Powder Bed Fusion at Higher Energy Densities

Mechanical properties of laser powder bed fusion processed Inconel alloy IN718 in different heat treatment conditions through small scale specimen testing

A review on microstructure, mechanical behavior and post processing of additively manufactured Ni-based superalloys

Influence of Deposition Parameters on Hardness Properties of InconelTM 718 Processed by Laser Powder Bed Fusion for Space Applications

High-throughput investigation of laser powder bed fabricated Inconel 718 alloy: Fabrication, microstructure and performance

Laser shock peening as a post-processing technique for Inconel 718 components manufactured by laser powder bed fusion

Mechanical Characterization of Near-Isotropic Inconel 718 Fabricated by Laser Powder-Bed Fusion

Microstructure and mechanical properties at elevated temperatures of as-built and heat-treated Inconel 718 produced through laser powder bed fusion processes

Experimental investigation of process parameter variations on the microstructure and failure behavior of IN718 structures in PBF-LB/M

Laser Powder Bed Fusion of Inconel 718 on 316 Stainless Steel