Abstract:The significant characteristics of the nickel-based Inconel 718 (IN718) superalloy are high strength, fatigue capacity, rupture strength, corrosion resistance, and creep resistance at temperatures exceeding 650 °C, which opens the application of IN718 for aircraft parts. The mechanical properties and surface residual stress (SRS) of the IN718 superalloy have been affected by fabrication and post-processing procedures, which shorten the service life of components. For the fabrication of complex aviation components, additive manufacturing of aerospace materials like IN718 has opened up new production techniques. However, localized melting and solidification produce anisotropy microstructure and a crystallographic texture with substantial tensile residual stress. These are responsible for mechanical anisotropy and pose metrological challenges for diffraction-based SRS detection. Knowing the magnitude and nature of SRS is crucial since they affect a mechanical properties and life of the parts. In this study, IN718 alloys were fabricated using the laser-based powder bed fusion (L-PBF) technique, and the impact of the standard ageing heat treatment (SAHT) process was assessed. The as-fabricated (AF) IN718 microstructure was found to have columnar dendritic structure and Laves phases in the interdendritic regions along the build direction. The SAHT sample microstructure led to the homogeneous precipitation of γ ′ and γ ′′ strengthening phases with δ and brittle Laves phases in grain boundaries. The average grain size of 41.56 μm in AF samples was increased to 44.80 μm after SAHT. The reduction of dislocation movements resulted in converting low angle grain boundaries found in the AF sample to high angle grain boundaries. SAHT samples displayed cubical texture along the and directions in the (001) plane. Following SAHT, there were increases in yield and ultimate tensile strength of 26.44% and 44.74%, respectively. On the other hand, the degree of elongation decreased to 36.19%. TRS in AF samples was converted into compressive surface residual stress following SAHT due to the phase transition. The process–structure–property relationship and the impacts of SAHT on the mechanical characteristics of the IN718 produced by L-PBF have been improved upon through this study.

Effect of post-processing on microstructure and mechanical properties of Alloy 718 fabricated using powder bed fusion additive manufacturing processes

Experimental investigation of process parameter variations on the microstructure and failure behavior of IN718 structures in PBF-LB/M

Study on the Effect of Powder-Bed Fusion Process Parameters on the Quality of as-Built IN718 Parts Using Response Surface Methodology

Additive Manufacturing of Alloy 718 via Electron Beam Melting: Effect of Post-Treatment on the Microstructure and the Mechanical Properties

A review on microstructure, mechanical behavior and post processing of additively manufactured Ni-based superalloys

Microstructure and mechanical properties at elevated temperatures of as-built and heat-treated Inconel 718 produced through laser powder bed fusion processes

On machining-induced surface integrity of Inconel 718 fabricated by powder bed fusion

Powder Bed Fusion of nickel-based superalloys: A review

Post-processing effects on the surface characteristics of Inconel 718 alloy fabricated by selective laser melting additive manufacturing

Inconel 718 produced by laser powder bed fusion: an overview of the influence of processing parameters on microstructural and mechanical properties

Effects of a modified heat-treatment on microstructure and mechanical properties of additively manufactured Inconel 718

Investigations on microstructure, crystallographic texture evolution, residual stress and mechanical properties of additive manufactured nickel-based superalloy for aerospace applications: role of industrial ageing heat treatment

Effect of parameters on quality of IN718 parts using laser additive manufacturing

Heterogeneous structures in a Ni-based superalloy with tailoring mechanical properties produced by a twin laser powder bed fusion system

Mechanical properties of laser powder bed fusion processed Inconel alloy IN718 in different heat treatment conditions through small scale specimen testing

Specific Characteristics of Materials Produced by Additive Manufacturing as Compared to Those Produced by Established Manufacturing Methods taking the Example of Alloy 718

Effect of Electric Pulse Treatment on Microstructure and Mechanical Property of Laser Powder Bed Fused IN718

Effect of homogenization and solution treatments time on the elevated-temperature mechanical behavior of Inconel 718 fabricated by laser powder bed fusion

A study of the influence of novel scan strategies on residual stress and microstructure of L-shaped LPBF IN718 samples

Effect of Preheating Temperature on Microstructural and Mechanical Properties of Inconel 718 Fabricated by Selective Laser Melting

Knowledge of process-structure-property relationships to engineer better heat treatments for laser powder bed fusion additive manufactured Inconel 718