Abstract:Laser-based metal additive manufacturing technology, which is represented by laser powder bed fusion (LPBF) and direct energy deposition (DED), has been widely used in high-end industries such as aerospace. However, with the rapid development of aerospace equipment, it has become increasingly difficult to meet the requirements of integrated design and manufacturing of metal parts by using LPBF or DED alone. LPBF/DED hybrid laser additive manufacturing technology is expected to greatly improve the overall manufacturing capacity of metal components by combining the advantages of the two technologies. It is expected to break through the limitation of overall manufacturing size, to realize the manufacturing of large and complex aerospace parts, and to reduce the number of components required for large and complex structures to meet the overall design and manufacturing requirements. In this paper, AlSi10Mg was selected as the build material for the LPBF/DED hybrid laser additive manufacturing process and the microstructure and mechanical properties of the as-built samples were studied. The analyses of the microstructure show that there are no obvious defects at the interface between the LPBF zone and the DED zone. Although the phase compositions of both the LPBF zone and the DED zone are composed of alpha-Al matrix and eutectic Si, the melt track shape, microstructural morphology, grain size, grain boundary angle distribution and grain texture change significantly around the LPBF/DED interface. The results of mechanical property tests indicated that the LPBF zone has higher microhardness and tensile strength but lower elongation in comparison with the DED zone. The fine microstructure containing a large number of Si-rich nano-precipitates and high amount of solid solution element enhance the microhardness and tensile strength of the LPBF zone, where the lower solid solubility and high percentage of low angle grain boundary increased the elongation of the DED zone. More importantly, the tensile strength of the LPBF/DED interface is not less than the DED zone, and the boundary of DED melt track as well as porosity defect in the DED zone are the weakest region of LPBF/DED hybrid laser additive manufacturing AlSi10Mg specimens. Therefore, the overall tensile strength of the sample is mainly determined by the DED zone. The formation mechanism of the gradient microstructure around the LPBF/DED interface and the effect of microstructure on properties were also analyzed. This paper proves that the LPBF/DED hybrid laser additive manufacturing technology can be used for the overall manufacturing of aluminum alloy components with regular surface structure.

Comparing microstructure and mechanical properties of AlSi10 alloy produced by powder bed fusion-laser beam and high pressure die casting

Effect of Aluminium Content and Processing Parameters on the Microstructure and Mechanical Properties of Laser Powder-Bed Fused Magnesium-Aluminium (0, 3, 6, 9wt%) Powder Mixture

Microstructure and mechanical properties of AlSi10Mg alloy built by laser powder bed fusion/direct energy deposition hybrid laser additive manufacturing

In-situ mechanical and microstructural characterization of miniaturized Al-Mg-Sc-Zr and AlSi10Mg specimens processed by laser powder-bed fusion (PBF-LB)

Formability and microstructure of laser powder bed fused AlSi10Mg alloy sheets under various deformation conditions

Additive Manufacturing of Al-12Si Alloy by Powder Laser Bed Fusion: an Investigation into its Microstructural Processes Formation and its Effects on Mechanical Behavior

Micromechanical Modeling of AlSi10Mg Processed by Laser-Based Additive Manufacturing: From as-Built to Heat-Treated Microstructures

Comparison of microstructure, crystallographic texture, and mechanical properties in Ti–15Mo–5Zr–3Al alloys fabricated via electron and laser beam powder bed fusion technologies

Solidification Mechanism of Microstructure of Al-Si-Cu-Ni Alloy Manufactured by Laser Powder Bed Fusion and Mechanical Properties Effect

The effect of the iso‐thermal heat treatment on the microstructure and properties of powder bed fusion‐laser beam AlSi10Mg alloy

Investigating the microstructural and mechanical characteristics of laser additive manufactured AlSi10Mg specimens through experimental and phase‐field modelling approaches

Heterogeneous structures in a Ni-based superalloy with tailoring mechanical properties produced by a twin laser powder bed fusion system

Persistent Homology Analysis of the Microstructure of Laser-Powder-Bed-Fused Al–12Si Alloy

Machine-Learning Assisted Laser Powder Bed Fusion Process Optimization for AlSi10mg: New Microstructure Description Indices and Fracture Mechanisms

Microstructural analysis of the influences of platform preheating and post-build heat treatment on mechanical properties of laser powder bed fusion manufactured AlSi10Mg alloy

Effects of the microstructure and texture characteristics on mechanical properties of the Al–Ni–Cu–Fe alloy manufactured by laser powder bed fusion

Heterogeneous microstructure and mechanical behaviour of Al-8.3Fe-1.3V-1.8Si alloy produced by laser powder bed fusion

Microstructure and mechanical property comparison of Inconel alloys fabricated using micro and conventional laser powder bed fusion

Review on the correlation between microstructure and mechanical performance for laser powder bed fusion AlSi10Mg

Comparison of AlSi7Mg0.6 alloy obtained by selective laser melting and investment casting processes: Microstructure and mechanical properties in as-built/as-cast and heat-treated conditions

Effect of heat treatments on microstructure and mechanical properties of AlSi10Mg alloys fabricated by laser powder bed fusion