Abstract:The microstructures and the mechanical properties of a laser powder bed fusion (LPBF) manufactured alloy coupons that were compositionally graded with austenitic stainless steel 316 L and bronze (Cu10Sn), which are immiscible, were investigated. While the microstructure of the pure 316 L contains only columnar γ-Fe grains, the formation of the equiaxed α-Cu, with α-Fe particles embedded in them, at the grain boundaries of the γ-Fe grains was observed upon alloying with Cu10Sn, for up to 50 wt.%. In the graded alloys with > 50 wt.% Cu10Sn, the microstructure inverts and contains α-Fe particle embedded α-Cu matrix along with some scattered γ-Fe grains. The two-dimensional phase-field simulations were employed to reproduced the phase transition and microstructure evolution in different compositions, revealing that the nucleation of γ-Fe occurs synchronously with the spinodal decomposition of liquid and that with further cooling, Cu-rich liquid solidifies and nanoscale spherical γ-Fe precipitates appear. Cross-sections with 10–40 wt.% Cu10Sn were found structurally unreliable owing to the formation of liquation cracks and shrinkage pores, whereas the rest of the build contained few pores and was crack-free. The Scheil solidification simulations together with the crack susceptibility index calculations over the entire compositions range of the CGA, reveal that when with < 50 wt.% Cu10Sn, liquid feeding to interdendritic regions of γ-Fe is limited, which is otherwise necessary to mitigate shrinkage-induced stresses. The hardness, yield and tensile strengths of the compositionally graded alloy in the cross-section with 50 wt.% Cu10Sn are higher than those of the parent constituents and the one with 80 wt.% Cu10Sn has the best combination of strength and ductility. The variations in strength and ductility are attributed to the microstructural and compositional changes in α-Cu matrix that were influenced by the formation of α-Fe particles. Finally, the appropriate proportions and the influence of the LPBF method in successfully mixing Cu10Sn and SS316L was discussed.

Composition design method of Al-Cu alloy for laser powder bed fusion

High strength Al–Li alloy development for laser powder bed fusion

Effect of Aluminium Content and Processing Parameters on the Microstructure and Mechanical Properties of Laser Powder-Bed Fused Magnesium-Aluminium (0, 3, 6, 9wt%) Powder Mixture

Laser powder bed fusion of a Cu-Ni-Al alloy using the compositional grading approach

Developing a novel lightweight Al–Mg–Li alloy for laser powder bed fusion additive manufacturing: Parameter optimization, microstructure evolution, and mechanical performance

Additive manufacturing of high strength copper alloy with heterogeneous grain structure through laser powder bed fusion

Development of a high strength Zr/Sc/Hf-modified Al-Mn-Mg alloy using Laser Powder Bed Fusion: Design of a heterogeneous microstructure incorporating synergistic multiple strengthening mechanisms

Effective Control of Microstructure Evolution in AZ91D Magnesium Alloy by SiC Nanoparticles in Laser Powder-Bed Fusion

Exploiting the rapid solidification potential of laser powder bed fusion in high strength and crack-free Al-Cu-Mg-Mn-Zr alloys

Preparation of Cu-Cr-Zr Alloy by Laser Powder Bed Fusion: Parameter Optimization, Microstructure, Mechanical and Thermal Properties for Microelectronic Applications

Developing ductile and isotropic Ti alloy with tailored composition for laser powder bed fusion

Mechanical behavior and microstructure evolution of Al-Cu-Mg alloy produced by laser powder bed fusion: Effect of heat treatment

Microstructural Evaluation and Tensile Properties of Al-Mg-Sc-Zr Alloys Prepared by LPBF

Processing defect, microstructure evolution and mechanical properties of laser powder bed fusion Al-12Si alloys

Effect of Ti microalloying and laser remelting on the microstructure and mechanical properties of laser powder bed fusion Al-12Si alloy

Strong and ductile Al–Mn–Mg–Sc–Zr alloy achieved in fabrication-rate enhanced laser powder bed fusion

Laser powder bed fusion of immiscible steel and bronze: A compositional gradient approach for optimum constituent combination

Heterogeneous microstructure and mechanical behaviour of Al-8.3Fe-1.3V-1.8Si alloy produced by laser powder bed fusion

Research Status of Laser Powder Bed Fusion Al–Li Alloys and Its Improvement Measures

Effect of Powder Spreading Parameters on Laser Absorption Behavior and Processability of High‐Strength Aluminum Alloy Fabricated by Laser Powder Bed Fusion

Effects of the microstructure and texture characteristics on mechanical properties of the Al–Ni–Cu–Fe alloy manufactured by laser powder bed fusion