Abstract:Magnesium alloys WE43 and AZ91D offer weight savings for structural applications. WE43 contains rare-earth elements such as yttrium and neodymium, whereas AZ91D and the AZ class of alloys are lower-cost containing aluminium and zinc. This work uses a modified version of the latter, identified as AZ91D*, where calcium and yttrium have been added. Laser Engineered Net Shaping (LENS) equipment was used to investigate the 3D printing behaviour of gas-atomized WE43 and AZ91D* material. Process evaluations were first done using single track laser scans across wrought substrates of WE43 and AZ31. Process parameters were then developed that enabled deposition of build coupons with less than 1% porosity. These were used for microstructural and mechanical property assessments. The energy densities used were in the range of 40 – 60 J/mm2 for AZ91D*, while for WE43 a value of 50 J/mm2 was selected. A focus of the work was managing the tendency of magnesium materials to fume heavily during deposition, while achieving a deposit with close to nominal density, i.e. having a low incidence of voids or other micro- or macro-structural defects. The porosity of AZ91D* builds did not seem to correlate with increasing deposition energy density, however WE43 builds did, up to a practical limit imposed by generation of excessive fume. WE43 generated much less fume than AZ91D*. Analysis of the input powder materials indicate the presence of oxides on the particle surfaces. The WE43 powders had a noticeable shell of yttrium oxide. The microstructures of WE43 builds show the presence of arc-shaped structures that are likely the same yttrium oxides, partially, or fully 'unfolded'. Tensile testing was conducted on WE43 build coupons to assess the effect of a T6 heat treatment. The effect on the ultimate tensile and yield strengths was negligible, however the % elongation at break almost doubled. Inspection of the fracture surfaces suggests this was due to a change in mechanism from fracture initiation at sites of lack-of-fusion/un-melted particles, to a more ductile micro-void coalescence. Furthermore, a not previously described microstructure anomaly was observed: the presence of pure elemental magnesium crystallites and films on the fracture surface. These are attributed to condensation of magnesium vapour on previously built layers and are a possible reason for the existence of lack-of-fusion defects. The in-depth study of process fundamentals will enable future work on process fume inhibition based on process optimization and alloy composition with the goal of producing parts for biomedical and lightweighting applications.

Preparation of the high compressive performance special-shaped C sf /AZ91D composite part using the liquid-solid extrusion following vacuum pressure infiltration process

Effective Control of Microstructure Evolution in AZ91D Magnesium Alloy by SiC Nanoparticles in Laser Powder-Bed Fusion

Microstructures and Mechanical Properties of Engineered Short Fibre Reinforced Aluminium Matrix Composites

Microstructure and Mechanical Properties of AZ91 Rein-Forced with High Volume Fraction of Oriented Short Carbon Fibers

Development of AZ91D Magnesium Alloy-Graphene Nanoplatelets Composites Using Thixomolding Process

Microstructure and Mechanical Properties of Squeeze Casting Quasicrystal Reinforced AZ91D Magnesium Matrix Composites

Effect of fabrication parameters on carbon fibre reinforced magnesium matrix composite components

Preparation of Al2O3/AZ91D Mg Interpenetrating Composites Using Lost Foam Casting Combined with Layered Extrusion Forming

Tensile and fatigue behavior of carbon fiber reinforced magnesium composite fabricated by liquid-solid extrusion following vacuum pressure infiltration

Highly thermal conductive C sf /Mg composites by in-situ constructing the unidirectional configuration of short carbon fibers

Preparation and properties of nano-sized SiC particles reinforced AZ91D magnesium matrix composites

Additive manufacturing of WE43 and modified AZ91D magnesium alloys using the laser engineered net shaping process

Hybrid Filler Actions on Functional Performance Evaluation of Magnesium Alloy (AZ61) Hybrid Nanocomposites

Fabrication of nano-SiCp/AZ91D composites by high-intensity ultrasonic method

Fabrication and mechanical properties of novel CFRP/Mg alloy hybrid laminates with enhanced interface adhesion

Characteristics performance evaluation of AZ91-fly ash composite developed by vacuum associated stir processing

Selective laser melted AZ91D magnesium alloy with superior balance of strength and ductility

Effects of Cyclic Extrusion and Compression on the Microstructure and Mechanical Properties of AZ91D Magnesium Composites Reinforced by SiC Nanoparticles

Fabrication of Carbon Nanotubes Reinforced AZ91D Composites by Ultrasonic Processing

Microstructures and Mechanical Properties of Carbon Tubes Reinforced AZ91D Magnesium Matrix Composites Prepared by Squeeze Casting

Wear Characteristics of Mg Alloy AZ91 Reinforced with Oriented Short Carbon Fibers