Abstract:In this study, AZ91/23 vol.% short carbon fiber composite was produced by a squeeze casting technique using a cylindrical pre-form of treated carbon fibers, in which the fibers are randomly oriented in the horizontal plane. Cylindrical specimens (height = 9 mm and diameter = 6 mm) were machined from the as-cast AZ91 matrix and its composite. The full behavior of the produced composite was studied through the test specimens machined in two directions, namely parallel to the reinforced plane (in the radial direction of the cast cylinder) and normal to the reinforced plane (in the axial direction of the cast composite). The microstructures of the produced composite specimens were investigated using SEM equipped with EDS analysis. Density, hardness, compressive, and wear behavior were also investigated. For comparison, the AZ91 matrix was evaluated as a reference. The microstructure of the produced AZ91 matrix alloy and its composite revealed dense materials without casting defects. Both composite specimens show improvement in hardness, compressive strength, and wear properties over the AZ91 matrix. The compressive and wear properties are more fiber orientation-dependent than the hardness results. The parallel composite specimen depicts the highest compressive properties in terms of yield compressive strength (311 MPa) and ultimate compressive strength (419 MPa), compared to that shown by the AZ91 matrix and the normal composite specimen. This improvement in compressive strength was at the expense of ductility. The parallel composite specimen shows the lowest ductility (R = 3.8%), compared to that given by the normal composite specimen (R = 7.1) and the AZ91 matrix alloy (R = 13.6). The wear testing results showed that at the highest wear load of 5 N, the material weight loss of the parallel composite specimen decreases by 44% and 64% compared to the AZ91 matrix and the normal composite specimen, respectively.

Microstructures and Mechanical Properties of Carbon Tubes Reinforced AZ91D Magnesium Matrix Composites Prepared by Squeeze Casting

Microstructure and Mechanical Properties of Squeeze Casting Quasicrystal Reinforced AZ91D Magnesium Matrix Composites

Mechanical properties and fabrication of carbon nanotubes reinforced AZ91D magnesium matrix nanocomposites

Fabrication of Carbon Nanotubes Reinforced AZ91D Composites by Ultrasonic Processing

Tribological Behavior of Carbon Nanotube-Reinforced AZ91D Composites Processed by Cyclic Extrusion and Compression

Effect of Heat Treatment on Microstructure and Mechanical Properties of Squeeze Cast n SiCp/AZ91D Magnesium Matrix Composites

Microstructure, Interface and Strengthening Mechanism of Ni-CNTs/AZ91 Magnesium Matrix Composites

Toughening and strengthening of Cu-coated carbon nanotubes reinforced AZ61 magnesium matrix nanocomposites by improving interfacial bonding

Experimental study of squeeze casting of ZK60 magnesium alloy

Study on Pressurized Solidification Behavior and Microstructure Characteristics of Squeeze Casting Magnesium Alloy AZ91D

Rapid microwave sintering of carbon nanotube-filled AZ61 magnesium alloy composites

Squeeze Cast Mg-Zn Alloys for Bioapplications: Tensile Properties and Microstructure

Effect of CNTs on microstructure, mechanical and wear properties of the AZ91–3B 4 C–3SiC– x CNTs composites

Development of AZ91D Magnesium Alloy-Graphene Nanoplatelets Composites Using Thixomolding Process

Microstructure and Mechanical Properties of AZ91 Rein-Forced with High Volume Fraction of Oriented Short Carbon Fibers

Tensile Deformation and Fracture of Unreinforced AZ91 and Reinforced AZ91-C at Temperatures up to 300 °C

Effect of carbon nanotubes grown temperature on the fracture behavior of carbon fiber reinforced magnesium matrix composites: Interlaminar shear strength and tensile strength

On the role of carbon nanotubes addition in carbon fiber-reinforced magnesium matrix composites

Influence of Soft Phase and Carbon Nanotube Content on the Properties of Hierarchical AZ61 Matrix Composite with Isolated Soft Phase

Microstructure and Mechanical Properties of Squeezing Casting Mg-Nd-Gd-Zn-Zr Alloy

Developing Fittingly Comprehensive Performance Carbon Nanotube/Mg-6Zn Sheets with Substantial Enhancement in Formability