Abstract:The Mg-Al series alloys are well known for their low density, high specific strength, and superior damping capability. However, the application of Mg-Al series alloys is often limited by inadequate mechanical properties. To fulfill the growing demand for lightweight structural components, ultrafine grained magnesium alloys with superior mechanical properties have gained attention. Mechanical milling and powder metallurgy were used to produce the AZ61 ultra-fine grained magnesium alloy with super-high tensile characteristics. The effects of mechanical milling on the grain size, precipitates, texture, and tensile properties of AZ61 ultra-fine grained magnesium alloy were investigated. The grain size of the AZ61 alloy produced by mechanical milling and powder metallurgy was reduced from 0.91 mu m to 0.68 mu m when compared to that produced by non-mechanical milling. Mechanical milling accelerated the dynamic precipitation and refining of Mg 17Al 12 while weakening the basal texture. The yield strength, tensile strength, and elongation of AZ61 ultra-fine grained magnesium alloy are 393.1 MPa, 431.9 MPa, and 8.5%, respectively, which are superior to the AZ61 alloy produced by other processes. The theoretical grain refinement and Orowan strengthening mechanisms of AZ61 alloy were calculated, and it shows that the grain refinement strengthening contributes more than 90% of the yield strength. The Orowan strengthening was overestimated when Mg 17Al 12 was distributed at grain boundaries. The weakening of basal texture resulted in a reduction in yield strength. The fracture mechanism of the AZ61 alloy without mechanical milling is dominated by oxidation on the surface of the AZ61 powder, which initiates interparticle debonding. The fracture mechanism of the AZ61 alloy with mechanical milling is dominated by deformation mismatch between the deboned powders and the stronger bonded powders, and the increase in the amount of Mg 17Al 12 along the grain boundary.

Microstructures and Mechanical Properties Ofaz91d Magnesium Alloy Processed by Low Pressure Die Casting

Processing Technology and Mechanical Properties of Die-Cast Magnesium Alloy AZ91D

On the Deformation Behavior of Heterogeneous Microstructure and Its Effect on the Mechanical Properties of Die Cast AZ91D Magnesium Alloy

Microstructure and Mechanical Properties of Squeeze Casting Quasicrystal Reinforced AZ91D Magnesium Matrix Composites

Low-pressure die casting of magnesium alloy AM50: Response to process parameters

Study on Mechanical Properties of Vacuum Die-cast AZ91D Magnesium Alloy

Effect of Aluminium Content and Processing Parameters on the Microstructure and Mechanical Properties of Laser Powder-Bed Fused Magnesium-Aluminium (0, 3, 6, 9wt%) Powder Mixture

Research on the Comparison of the Macroscopic Defect and the Mechanical Property of AZ91D Magnesium Alloy Parts Produced by Liquid Combination Process of Die Casting and Forging and Liquid Die Casting

Failure Behavior of High Pressure Die Casting AZ91D Magnesium Alloy

Investigation of Properties in Magnesium Alloy Thin Plates after Die Casting Processes

Microstructure and Properties of AZ61 Ultra-Fine Grained Magnesium Alloy Prepared by Mechanical Milling and Powder Metallurgy Processing

Effect of Extrusion on Mechanical Properties of AZ91 Cast Magnesium Alloy

Study on Pressurized Solidification Behavior and Microstructure Characteristics of Squeeze Casting Magnesium Alloy AZ91D

Effective Control of Microstructure Evolution in AZ91D Magnesium Alloy by SiC Nanoparticles in Laser Powder-Bed Fusion

Influence of Melt Flow in the Gating System on Microstructure and Mechanical Properties of High Pressure Die Casting AZ91D Magnesium Alloy

Effect of Different Casting Techniques on the Microstructure and Mechanical Properties of AE44-2 Magnesium Alloy

Mechanical Properties and Microstructures of Mg-Al-Zn Alloys with High Aluminum Contents

Correlation of 3D Defect-Band Morphologies and Mechanical Properties in High Pressure Die Casting Magnesium Alloy

Selective laser melted AZ91D magnesium alloy with superior balance of strength and ductility

Comparative Study of the Cavity Pressure of Magnesium Alloy and Aluminium Alloy During Die Casting Process