97-Watt, 1.08-Gigahertz Repetition Rate, Femtosecond Yb:fiber Laser Source

Yan Wang,Yizhou Liu,Zhigang Zhang,Franz X. Kartner

DOI: https://doi.org/10.1364/cleopr.2020.c2a_2

2020-01-01

Abstract:We demonstrate a femtosecond ytterbium-doped fiber laser at 1030 nm with 1.08 GHz repetition rate, 97 W average output power using chirped pulse amplification (CPA). The compressed output pulse width is 233 fs.

What problem does this paper attempt to address?

66 fs, 3 W all fiber Yb3+-doped mode-locked fiber laser

minglie hu,lu chai,weidong shen,xu liu,chingyue wang,han chi,bowen liu,youjian song

DOI: https://doi.org/10.1364/fbta.2014.fth4f.3

2014-01-01

Abstract:We present a mode-locked all-normal-dispersion double-clad Yb-doped fiber laser with 3 W output average power at 81 MHz repetition rate for 37 nJ chirped pulses, which can be compressed to 66 fs, with 400 KW peak power.
Fiber-solid, Hybrid, Single-Frequency Laser (100 W) with a 100 MHz Repetition Rate and 1 Ns Pulse Width from a Spherical Aberration Compensated Four-Stage Nd:YVO4 Amplifier

Xiang Zhang,Yi Wang,Bin Liu,Chunhua Wang,Zhen Xiang,Chong Liu

DOI: https://doi.org/10.1364/ao.53.005058

IF: 1.9

2014-01-01

Applied Optics

Abstract:A pulsed laser for laser guide stars with a 100 MHz repetition rate and 1 ns pulse width was achieved by external modulation of a continuous wave (CW) laser with a 70 kHz spectrum width. The laser is amplified first by two fiber pre-amplifiers and then by four solid-state power amplifiers. The laser achieves gains as high as 36 dB in the fiber pre-amplifiers due to the long gain medium length. The output power from the fiber amplifiers is 2.1 W. The laser receives further amplification in the solid-state amplifiers and retains good beam quality by aberration compensation. The final output average power is 102.9 W, and the beam quality factor M-2 is 1.46. The laser reaches high power without spectrum width and pulse width broadening at the 100 MHz repetition rate. The spectrum width of the pulsed laser is less than 0.8 GHz, which is close to the Fourier transform limit. Such a laser with single-frequency, high-repetition, and high-power features along with good beam quality will be valuable for many research areas. (C) 2014 Optical Society of America
Amplification of 1.08 GHz Repetition Rate Femtosecond Laser Pulses to 97 W Average Power by a Fiber Amplifier

Yan Wang,Yizhou Liu,Zhigang Zhang,Franz Kaertner

DOI: https://doi.org/10.1364/osac.423499

2021-01-01

OSA Continuum

Abstract:We demonstrate a femtosecond Yb:fiber laser amplification system which delivers 97 W average output power at a repetition rate of 1.08 GHz using a rod-type photonic crystal fiber. The re-compressed output pulse is 233 fs. Numerical simulation was also conducted in agreement with our experimental results.
Femtosecond Amplifier Similariton Yb:fiber Laser at a 616 MHz Repetition Rate.

Chen Li,Guizhong Wang,Tongxiao Jiang,Peng Li,Aimin Wang,Zhigang Zhang

DOI: https://doi.org/10.1364/ol.39.001831

IF: 3.6

2014-01-01

Optics Letters

Abstract:We report a compact Yb:fiber ring laser operated at 616 MHz. The average output power is 450 mW at a pump power of 900 mW. The dechirped pulse width is 98 fs.
750 MHz Fundamental Repetition Rate Femtosecond Yb:fiber Ring Laser.

Chen Li,Guizhong Wang,Tongxiao Jiang,Aimin Wang,Zhigang Zhang

DOI: https://doi.org/10.1364/ol.38.000314

2013-01-01

Abstract:We report a compact Yb:fiber ring laser operated at 750 MHz. The average output power is 210 mW at a pump power of 1.8 W. The dechirped pulse width is 68 fs.
3 GHz, Fundamentally Mode-Locked, Femtosecond Yb-fiber Laser.

Hung-Wen Chen,Guoqing Chang,Shanhui Xu,Zhongmin Yang,Franz X. Kaertner

DOI: https://doi.org/10.1364/ol.37.003522

IF: 3.6

2012-01-01

Optics Letters

Abstract:We demonstrate a fundamentally mode-locked Yb-fiber laser with 3 GHz repetition rate and ∼206 fs pulse duration. The laser incorporates two enabling technologies: a 1 cm heavily Yb-doped phosphate glass fiber as the gain medium and a high-dispersion (-1300 fs2) output coupler to manage cavity dispersion. The oscillator self-starts and generates up to 53 mW average power.
1.2 GHz Repetition Rate Stretched-pulse from a Femtosecond Solid-state Yb: Fiber Laser

Ya Wang,Ruoao Yang,Zhendong Chen,Duo Pan,Bin Luo,Zhigang Zhang,Jingbiao Chen

DOI: https://doi.org/10.1364/fio.2023.fd2.5

2023-01-01

Abstract:A 1.2 GHz, 106 fs stretched-pulse mode-locked laser was demonstrated, with > 700 mW output power. To the best of our knowledge, this is the highest repetition rate from NPE mode locked Yb: fiber lasers.
112-Μj 180-Fs Pulses at 1-Khz Repetition Rate from Yb-Doped Laser Based on Strictly All-Fiber CPA Structure

Decai Deng,Haitao Zhang,Qihang Gong,Linlu He,Jiaqi Zu

DOI: https://doi.org/10.1109/jphot.2019.2948043

IF: 2.4

2019-01-01

IEEE Photonics Journal

Abstract:In this paper, we reported an Yb-doped, femtosecond, chirped pulse amplification laser based on strictly all-fiber structure. It operated at a low repetition rate of 1 kHz and adopted the synchronously pumping technology to suppress ASE and heat accumulation. A chirped fiber Bragg grating providing adjustable dispersion is used as the pulse stretcher. High order dispersion induced by fiber, grating pair in the system was compensated accurately. Laser pulse with duration of 180 fs and energy of 112 μJ has been obtained. In addition, it has a high long-term stability of energy and a good beam quality, corresponding to energy fluctuation of 0.62% in an hour and M2 factor of 1.15, respectively.
3-Ghz, Ultrafast Yb-fiber Laser Sources: Closing the Spectral Gaps

Hung-Wen Chen,Jinkang Lim,Shanhui Xu,Zhongmin Yang,Franz X. Kaertner,Guoqing Chang

DOI: https://doi.org/10.1117/12.2060745

2014-01-01

Abstract:Many applications require GHz femtosecond pulses with the center wavelength tunable over a broad range. Recently we have demonstrated a 3-GHz, femtosecond Yb-fiber laser system with >12-W average power using the pre-chirp management method. Nonlinear wavelength conversion based on this powerful laser source has enabled us to derive 3-GHz femtosecond sources at other useful wavelengths: using stimulated Raman scattering inside photonic crystal fibers, we have implemented a femtosecond Raman soliton source tunable between 1.06-1.35 mu m; using fiber-optic Cherenkov radiation, we have demonstrated a 14-fs source centered at 850 nm with >300-mW average power.
72-Kw High-Peak-power Linearly-Polarized Single-Mode Pulsed Fiber Laser with 80 Khz Repetition Rate and 4.5 Ns Duration

J. He,P. Yan,X. Wushouer,J. Zhou,M. Gong

DOI: https://doi.org/10.1134/s1054660x10230052

IF: 1.2

2010-01-01

Laser Physics

Abstract:We reported a 26 W linearly polarized single-mode Yb-doped photonic crystal fiber amplifier, working at 80 kHz repetition rate with 4.5 ns duration, corresponding 72 kW peak power. Using a acousto-optic Q-switched Nd:YVO4 laser as the seed source, the 26 W average power of 1064 nm laser was obtained at a repetition rate of 80 kHz from a Yb-doped photonic crystal fiber amplifier, with 4.5 ns duration, polarization extinction ratio 11 dB and M 2 < 1.2.
73 Nj, 109 Fs Yb-doped Fiber Laser at 19 MHz Repetition Rate in Amplifier Similariton Regime

Yizhou Liu,Yifan Cui,Jian Zhang,Aimin Wang,Zhigang Zhang

DOI: https://doi.org/10.1364/prj.3.000248

IF: 7.6

2015-01-01

Photonics Research

Abstract:We report femtosecond pulse generation in an amplifier similariton oscillator and a prechirped fiber amplifier system. The final output power is 1.4W, and the fundamental repetition rate is 19.1 MHz after a single state fiber amplifier. The pulsewidth is 109 fs.
Old Wavelength, New Performance: Hectowatt 200-μJ-level Femtosecond fiber CPA System at 1064 Nm

Shang Wang,Qikai Zhao,Guanguang Gao,Zhenhua Cong,Zhaojun Liu,Zhigang Zhao

DOI: https://doi.org/10.1109/jlt.2023.3326072

IF: 4.7

2023-01-01

Journal of Lightwave Technology

Abstract:The Yb:fiber based high-power and high-energy ultrafast lasers usually feature central wavelength of 1030 nm instead of the more common one of 1064 nm, thus limiting some potential wavelength-dependent applications. In this work, a hectowatt 1064-nm femtosecond chirped pulse amplification (CPA) system based on double-stage rod-type photonic crystal fiber (PCF) amplifier was demonstrated, with a pulse energy of 212-μJ and a repetition rate of 0.5 MHz. Compared with our previous work [Opt. Express 30(6), 3611, 2022], two key measures were employed. Firstly, a Yb:YAG crystal was intentionally introduced as a spectral filter for avoiding 1030-nm amplified spontaneous emission (ASE) oscillation, which hence improved the signal-to-noise ratio (SNR) by 15 dB. Secondly, an additional stage of rod-type PCF amplifier was adopted for further power scaling, achieving an average power of 127 W. Finally, the pulse was compressed to ∼460 fs, with an average power of 106 W and a compression efficiency of ∼83%. The beam quality factors (M2) were measured to be M2 X = 1.12 and M2 Y = 1.09. To the best of our knowledge, this is the highest pulse energy among 1064-nm hectowatt-level femtosecond lasers, thus providing a high-quality source for wavelength-dependent applications. For example, it can be used as a driver for high-repetition-rate vacuum ultraviolet (VUV) sources about 10.5 eV, with an expected conversion efficiency of up to 1%.

engineering, electrical & electronic,optics,telecommunications
616 MHz Repetition Rate Sub-100Fs Amplifier-Similariton Yb:Fiber Laser

Chen Li,Guizhong Wang,Tongxiao Jiang,Peng Li,Aimin Wang,Zhigang Zhang

2014-01-01

Abstract:We report a compact Yb:fiber ring laser operated at 616 MHz. The average output power is 450 mW at a pump power of 900 mW. The dechirped pulse width is 98 fs.
All-Fiber High Repetition Rate Short Pulse Generation Around 1030Nm

Qin Li,Rui Zhu,Chi Zhang,Sigang Yang,Kenneth K. Y. Wong

DOI: https://doi.org/10.1117/12.904184

2011-01-01

Abstract:High repetition rate pulsed fiber laser in 1μm is an attractive and novel source for optical transmission systems, since ytterbium-doped fiber (YDF) has the potential to provide broad gain spectrum and high optical conversion efficiency in this regime. Previous works in this area have explored the wavelength range above 1050 nm. In this paper, we focus more on the shorter wavelength band which is closer to the peak of the emission cross section of YDF at around 1030 nm. A 10-GHz harmonically mode-locked all-fiber laser is demonstrated. A pulse train with a pulsewidth of around 13 ps and wavelength tunable from 1023.5 nm to 1053.3 nm is achieved. The side-mode suppression ratio is more than 50 dB without any stabilization techniques.
11-mJ pulse energy wideband Yb-doped fiber laser

Chundi Zheng,Haitao Zhang,WenYong Cheng,Minjie Liu,Ping Yan,Mali Gong

DOI: https://doi.org/10.1016/j.optcom.2012.04.033

IF: 2.4

2012-01-01

Optics Communications

Abstract:We report a wide bandwidth (Δλ=8nm) optical pulsed MOPA (master oscillator power amplifier) source emitting 11.23mJ pulses (1.25MW peak power) in the wavelength centered at (λ=1064nm). Pulse duration and repetition rate were 9ns and from 10Hz to 100Hz, respectively. In order to suppress amplified spontaneous emission (ASE), multi-stage pulse pump technology is applied. And the large core diameter (90μm) and wide bandwidth ensures the high peak power and energy output.
3 GHz, Yb-fiber laser-based, few-cycle ultrafast source at the Ti:sapphire laser wavelength

Hung-Wen Chen,Zia Haider,Jinkang Lim,Shanhui Xu,Zhongmin Yang,Franz X Kärtner,Guoqing Chang

DOI: https://doi.org/10.1364/OL.38.004927

2013-11-15

Abstract:We demonstrate a compact ultrafast source centered at 850 nm with >200 nm bandwidth (full width at half-maximum) based on a 3 GHz Yb-fiber master-oscillator-power-amplifier system. The output pulses (with up to 13 W average power) from the laser system are coupled into short (<50 mm) pieces of photonic crystal fibers to excite broadband fiber-optic Cherenkov radiation; the resulting broad phase-matching bandwidth due to short fiber length produces an upconverted spectrum spanning in the wavelength range of 750-950 nm with average power of 94, 184, and 380 mW for fiber length of 28, 37, and 48 mm, respectively. The spectrum generated from the 37 mm fiber is then dechirped by eight double-chirped mirrors, leading to compressed pulses ~14 fs in duration. Such an ultrafast source is a promising substitute of multigigahertz mode-locked Ti:sapphire lasers for applications in optical frequency metrology and multiphoton coherent microscopy.
Ultrafast Yb:YAG laser oscillator with gigahertz repetition rate

Moritz Seidel,Jérémie Pilat,Lukas Lang,Christopher R Phillips,Ursula Keller

DOI: https://doi.org/10.1364/OE.503697

2023-10-09

Abstract:We present a SESAM modelocked Yb:YAG solid-state laser providing low-noise narrowband pulses with a pulse duration of 606 fs at a 1.09-GHz repetition rate, delivering up to 2.5 W of average output power. This laser provides access to a new parameter space that could previously not be reached by solid-state lasers and, to the best of our knowledge, is the first modelocked solid-state Yb:YAG laser in the gigahertz regime. This is achieved by introducing a single additional intracavity element, specifically a nonlinear birefringent YVO4 crystal, for soliton formation, polarization selection, and cavity intensity clamping. The isotropic pump absorption in Yb:YAG allows for stable and low-noise operation with multimode fiber pumping. This laser is ideally suited as a seed source for many commercial high-power Yb-doped amplification systems operating at a center wavelength around 1.03 µm. The laser exhibits a high power per comb line of 5.0 mW which also makes it interesting for applications in frequency comb spectroscopy, especially if it is used to pump an optical parametric oscillator. We measure a relative intensity noise (RIN) of 0.03%, integrated from 1 Hz to 10 MHz. Furthermore, we show that the laser timing jitter for noise frequencies >2 kHz is fully explained by a power-dependent shift in the center wavelength of 0.38 nm/W due to the quasi-three-level laser gain material. The narrow gain bandwidth of Yb:YAG reduces this contribution to noise in comparison to other SESAM modelocked Yb-doped lasers.
A Sub-Nanosecond Narrow-Linewidth Pulsed Laser Source with Controllable Repetition Rate

L Q Niu,C X Gao,H D He,L Feng,Z Y Cao,C D Sun,S L Zhu

DOI: https://doi.org/10.1088/1054-660x/23/7/075101

IF: 1.2

2013-01-01

Laser Physics

Abstract:A compact all-fiber sub-nanosecond narrow-linewidth Yb-doped fiber amplifier with a controllable repetition rate has been investigated. Tunable temporal pulses ranging from sub-nanoseconds to 10 ns with repetition rates from 10 kHz to 1 MHz are obtained by controlling the waveform of the injected electrical-pulse signal. Due to the practical requirements of our intended applications, a distributed feedback semiconductor laser with a wavelength of 1064 nm, pulse duration of 802 ps, repetition rate of 500 kHz and average power of 20 μW is used to seed a dual-stage single mode Yb-doped fiber amplifier. The characteristics of the amplified pulses are measured and exhibit a temporal duration of 810 ps with an average power of 31.2 mW. The gain of the amplified pulse is about 32 dB at the maximum output power. A notable feature of the amplifier pulses is that the spectral linewidth can be maintained to less than 0.1 nm during the dual-stage amplifier process. The noise level lies more than 22 dB below the peak value of the amplified spectrum, which represents an excellent signal-to-noise ratio.
High-Energy Femtosecond Pulses From an Ytterbium-Doped Fiber Laser With a New Cavity Design

A. Albert,V. Couderc,L. Lefort,A. Barthelemy

DOI: https://doi.org/10.1109/lpt.2003.823103

IF: 2.6

2004-02-01

IEEE Photonics Technology Letters

Abstract:A new architecture which is based on the chirped pulse amplification scheme is proposed to increase the pulse energy of the mode-locked fiber laser. The idea was applied to a passively mode-locked laser using an ytterbium (Yb/sup 3+/)-doped double-clad silica fiber. Mode-locking was achieved by nonlinear polarization evolution associated to frequency-shifted feedback technique for self-starting. A compressor and a stretcher, based on diffraction gratings, permitted us to manage the dispersion and to reduce the pulse power in the fiber. The laser delivered chirped pulses at 1050 nm with 11.8-nJ energy at a 9.3-MHz repetition rate (110-mW average power) which were subsequently compressed to 196-fs duration.

engineering, electrical & electronic,optics,physics, applied
1 GHz Repetition Rate Ring Cavity Femtosecond Yb:fiber Laser

Chen Li,Xiang Gao,Guizhong Wang,Tongxiao Jiang,Aimin Wang,Zhigang Zhang

DOI: https://doi.org/10.1364/cleo_si.2014.sw3e.2

2014-01-01

Abstract:We demonstrate the first 1 GHz fundamental repetition rate ring cavity ytterbium doped fiber laser. The laser delivers 600 mW, 64fs near transform-limited pulses and supports direct octave-spanning spectrum generation.

97-Watt, 1.08-Gigahertz Repetition Rate, Femtosecond Yb:fiber Laser Source

66 fs, 3 W all fiber Yb3+-doped mode-locked fiber laser

Fiber-solid, Hybrid, Single-Frequency Laser (100 W) with a 100 MHz Repetition Rate and 1 Ns Pulse Width from a Spherical Aberration Compensated Four-Stage Nd:YVO4 Amplifier

Amplification of 1.08 GHz Repetition Rate Femtosecond Laser Pulses to 97 W Average Power by a Fiber Amplifier

Femtosecond Amplifier Similariton Yb:fiber Laser at a 616 MHz Repetition Rate.

750 MHz Fundamental Repetition Rate Femtosecond Yb:fiber Ring Laser.

3 GHz, Fundamentally Mode-Locked, Femtosecond Yb-fiber Laser.

1.2 GHz Repetition Rate Stretched-pulse from a Femtosecond Solid-state Yb: Fiber Laser

112-Μj 180-Fs Pulses at 1-Khz Repetition Rate from Yb-Doped Laser Based on Strictly All-Fiber CPA Structure

3-Ghz, Ultrafast Yb-fiber Laser Sources: Closing the Spectral Gaps

72-Kw High-Peak-power Linearly-Polarized Single-Mode Pulsed Fiber Laser with 80 Khz Repetition Rate and 4.5 Ns Duration

73 Nj, 109 Fs Yb-doped Fiber Laser at 19 MHz Repetition Rate in Amplifier Similariton Regime

Old Wavelength, New Performance: Hectowatt 200-μJ-level Femtosecond fiber CPA System at 1064 Nm

616 MHz Repetition Rate Sub-100Fs Amplifier-Similariton Yb:Fiber Laser

All-Fiber High Repetition Rate Short Pulse Generation Around 1030Nm

11-mJ pulse energy wideband Yb-doped fiber laser

3 GHz, Yb-fiber laser-based, few-cycle ultrafast source at the Ti:sapphire laser wavelength

Ultrafast Yb:YAG laser oscillator with gigahertz repetition rate

A Sub-Nanosecond Narrow-Linewidth Pulsed Laser Source with Controllable Repetition Rate

High-Energy Femtosecond Pulses From an Ytterbium-Doped Fiber Laser With a New Cavity Design

1 GHz Repetition Rate Ring Cavity Femtosecond Yb:fiber Laser