Abstract:The Yb:fiber based high-power and high-energy ultrafast lasers usually feature central wavelength of 1030 nm instead of the more common one of 1064 nm, thus limiting some potential wavelength-dependent applications. In this work, a hectowatt 1064-nm femtosecond chirped pulse amplification (CPA) system based on double-stage rod-type photonic crystal fiber (PCF) amplifier was demonstrated, with a pulse energy of 212-μJ and a repetition rate of 0.5 MHz. Compared with our previous work [Opt. Express 30(6), 3611, 2022], two key measures were employed. Firstly, a Yb:YAG crystal was intentionally introduced as a spectral filter for avoiding 1030-nm amplified spontaneous emission (ASE) oscillation, which hence improved the signal-to-noise ratio (SNR) by 15 dB. Secondly, an additional stage of rod-type PCF amplifier was adopted for further power scaling, achieving an average power of 127 W. Finally, the pulse was compressed to ∼460 fs, with an average power of 106 W and a compression efficiency of ∼83%. The beam quality factors (M2) were measured to be M2 X = 1.12 and M2 Y = 1.09. To the best of our knowledge, this is the highest pulse energy among 1064-nm hectowatt-level femtosecond lasers, thus providing a high-quality source for wavelength-dependent applications. For example, it can be used as a driver for high-repetition-rate vacuum ultraviolet (VUV) sources about 10.5 eV, with an expected conversion efficiency of up to 1%.

Yb-Doped Fiber Chirped Pulse Amplification System Delivering 1 mJ, 231 fs at 1 kHz Repetition Rate

112-Μj 180-Fs Pulses at 1-Khz Repetition Rate from Yb-Doped Laser Based on Strictly All-Fiber CPA Structure

Fiber-solid, Hybrid, Single-Frequency Laser (100 W) with a 100 MHz Repetition Rate and 1 Ns Pulse Width from a Spherical Aberration Compensated Four-Stage Nd:YVO4 Amplifier

Hybrid fiber-single crystal fiber chirped-pulse amplification system emitting more than 1.5 GW peak power with beam quality better than 1.3

72-Kw High-Peak-power Linearly-Polarized Single-Mode Pulsed Fiber Laser with 80 Khz Repetition Rate and 4.5 Ns Duration

A Sub-Picosecond Laser System Based on High-Energy Yb:YAG Chirped-Pulse Regenerative Amplification

All-fiber High Energy and Peak Power Broadband Yb-doped Fiber Amplifier

Low repetition rate broadband high energy and peak power nanosecond pulsed Yb-doped fiber amplifier

Amplification of 1.08 GHz Repetition Rate Femtosecond Laser Pulses to 97 W Average Power by a Fiber Amplifier

Pulsed Pumped Yb-doped Fiber Amplifier at Low Repetition Rate

Femtosecond Amplifier Similariton Yb:fiber Laser at a 616 MHz Repetition Rate.

Old Wavelength, New Performance: Hectowatt 200-μJ-level Femtosecond fiber CPA System at 1064 Nm

All-fiber 30-μm core diameter Yb-doped pulse-pumped amplifier cascade generating 10 nm-bandwidth 545 kW peak power pulses

High energy, single-polarized, single-transverse-mode, nanosecond pulses generated by a multi-stage Yb-doped photonic crystal fiber amplifier

Hundreds of picosecond pulses amplifier based on Yb-doped tapered fiber for the generation of 100 W average output power

Adaptively Controlled Sub-100 Fs Yb Fiber Chirped Pulse Amplification System

A 12 Mj 11 Ns Spectrally Narrow Fiber Amplifier with A Pulsed Pump

11-mJ pulse energy wideband Yb-doped fiber laser

Yb-doped Mode-Locked Fiber Laser Based on Pre-Chirp Managed Nonlinear Amplification

Development of a Femtosecond High-Power Ytterbium-doped Fiber Laser System and Study on Spiky Spectral Modulation in Highly Nonlinear Chirped-Pulse Fiber Amplifiers

Hundred Nano-Joules Polarization-Maintaining Yb-Doped Fiber Femtosecond Laser Amplification System