Abstract:This paper introduces a compact picosecond laser system using tapered double cladding fiber-single crystal fiber hybrid amplification technology for the first time. By modifying the Ginzburg-Landau equation, we established a simulation model and designed a passive mode-locked picosecond oscillator based on a semiconductor saturable absorber mirror. The oscillator outputs laser with a pulse width of 7.75 ps, a center wavelength of 1030.55 nm, and a spectrum width of 0.58 nm. The seed laser is stretched and amplified by the all-fiber front stage, and then injected into the tapered double cladding fiber-single crystal fiber hybrid amplifier. The laser power is amplified from 820 mw to 103.1 W, obtaining a gain of 21 dB. We used zero-phonon line pumping technology in single crystal fiber amplifier to reduce the thermal effects caused by quantum loss, thereby increasing the length of the crystal and increasing the power loading capacity. We designed a single crystal fiber amplification module using Yb:YAG with 60 mm long, 1 mm diameter and a 1 at.% doping rate for the first time. Finally a hundred-watt level picosecond laser output with a repetition frequency of 26.33 MHz, an average power of 103.1 W, a pulse width of 244.72 ps, a spectrum width of 1.16 nm, and a beam quality of M2 x = 1.368 and M2 y = 1.511 was obtained. To the best of our knowledge, this is the highest picosecond laser output power for an all-fiber front-stage combined with a single-stage single crystal fiber amplifier.

Hundred Nano-Joules Polarization-Maintaining Yb-Doped Fiber Femtosecond Laser Amplification System

Fiber-solid, Hybrid, Single-Frequency Laser (100 W) with a 100 MHz Repetition Rate and 1 Ns Pulse Width from a Spherical Aberration Compensated Four-Stage Nd:YVO4 Amplifier

Hundreds of picosecond pulses amplifier based on Yb-doped tapered fiber for the generation of 100 W average output power

Linearly-polarized single-transverse-mode high-energy multi-ten nanosecond fiber amplifier with 50W average power.

870 Fs, 448 Khz Pulses from an All-Polarization-maintaining Yb-doped Fiber Laser with a Nonlinear Amplifying Loop Mirror.

Femtosecond Mode-locked Fiber Laser at 1 Μm Via Optical Microfiber Dispersion Management

Amplification of 1.08 GHz Repetition Rate Femtosecond Laser Pulses to 97 W Average Power by a Fiber Amplifier

Compact hundred-watt level picosecond laser system based on tapered double cladding fiber-single crystal fiber hybrid amplifier

112-Μj 180-Fs Pulses at 1-Khz Repetition Rate from Yb-Doped Laser Based on Strictly All-Fiber CPA Structure

Low repetition rate broadband high energy and peak power nanosecond pulsed Yb-doped fiber amplifier

Yb-doped Mode-Locked Fiber Laser Based on Pre-Chirp Managed Nonlinear Amplification

72-Kw High-Peak-power Linearly-Polarized Single-Mode Pulsed Fiber Laser with 80 Khz Repetition Rate and 4.5 Ns Duration

Sub-60-fs, Compact 1100-Nm Fiber Laser System Based on Double-Pass Pre-Chirp Managed Amplification.

Multifunctional all-fiber polarization-maintaining nonlinear pulse amplifier

Figure-8 mode-locked Yb-doped fibre oscillator with a nonlinear amplifying loop mirror and power amplification

Development of a Femtosecond High-Power Ytterbium-doped Fiber Laser System and Study on Spiky Spectral Modulation in Highly Nonlinear Chirped-Pulse Fiber Amplifiers

Generation of 8-fs and 13-nJ pulse from a Yb-fiber system with nonlinear-pulse-compression

A 12 Mj 11 Ns Spectrally Narrow Fiber Amplifier with A Pulsed Pump

Research on ytterbium-doped photonic crystal fiber amplifier for the femtosecond fiber laser

Yb-Doped Fiber Chirped Pulse Amplification System Delivering 1 mJ, 231 fs at 1 kHz Repetition Rate

140 kHz, 1.2 ps pulses from an all-PM Yb-doped fiber master oscillator-power amplifier