Abstract:This paper introduces a compact picosecond laser system using tapered double cladding fiber-single crystal fiber hybrid amplification technology for the first time. By modifying the Ginzburg-Landau equation, we established a simulation model and designed a passive mode-locked picosecond oscillator based on a semiconductor saturable absorber mirror. The oscillator outputs laser with a pulse width of 7.75 ps, a center wavelength of 1030.55 nm, and a spectrum width of 0.58 nm. The seed laser is stretched and amplified by the all-fiber front stage, and then injected into the tapered double cladding fiber-single crystal fiber hybrid amplifier. The laser power is amplified from 820 mw to 103.1 W, obtaining a gain of 21 dB. We used zero-phonon line pumping technology in single crystal fiber amplifier to reduce the thermal effects caused by quantum loss, thereby increasing the length of the crystal and increasing the power loading capacity. We designed a single crystal fiber amplification module using Yb:YAG with 60 mm long, 1 mm diameter and a 1 at.% doping rate for the first time. Finally a hundred-watt level picosecond laser output with a repetition frequency of 26.33 MHz, an average power of 103.1 W, a pulse width of 244.72 ps, a spectrum width of 1.16 nm, and a beam quality of M2 x = 1.368 and M2 y = 1.511 was obtained. To the best of our knowledge, this is the highest picosecond laser output power for an all-fiber front-stage combined with a single-stage single crystal fiber amplifier.

Sub-60-fs, Compact 1100-Nm Fiber Laser System Based on Double-Pass Pre-Chirp Managed Amplification.

Fiber-solid, Hybrid, Single-Frequency Laser (100 W) with a 100 MHz Repetition Rate and 1 Ns Pulse Width from a Spherical Aberration Compensated Four-Stage Nd:YVO4 Amplifier

Vector-dispersion Compensation and Pulse Pedestal Cancellation in a Femtosecond Nonlinear Amplification Fiber Laser System.

Compact hundred-watt level picosecond laser system based on tapered double cladding fiber-single crystal fiber hybrid amplifier

Femtosecond Mode-locked Fiber Laser at 1 Μm Via Optical Microfiber Dispersion Management

High-power, 474 Fs, 31.12 MHz, All-Polarization-maintaining, 1560 Nm Fiber Laser System Based on the Chirped-Pulse Amplification

Environment-stable sub-100 fs Er: fiber laser with a 3 dB bandwidth of 78 nm

140 kHz, 1.2 ps pulses from an all-PM Yb-doped fiber master oscillator-power amplifier

589 nm laser generation by frequency doubling of a single-frequency Raman fiber amplifier in PPSLT.

Compact, repetition rate locked all-PM fiber femtosecond laser system based on low noise figure-9 Er:fiber laser

Sub-50 fs pulses generation from an all-fiber monolithic gain-managed nonlinear amplifier with CFBG-based pre-compressor

Yb-doped Mode-Locked Fiber Laser Based on Pre-Chirp Managed Nonlinear Amplification

Investigations of the High-Power, Single-Frequency, Sub-Microseconds, 1548-nm Fiber Laser Based on the Optical Pulse Modulation

Hundred Nano-Joules Polarization-Maintaining Yb-Doped Fiber Femtosecond Laser Amplification System

Old Wavelength, New Performance: Hectowatt 200-μJ-level Femtosecond fiber CPA System at 1064 Nm

Generation of 8-fs and 13-nJ pulse from a Yb-fiber system with nonlinear-pulse-compression

396 MHz CPA femtosecond laser system based on a single crystal fiber rod-type amplifier

Microjoule Level Femtosecond Optical Pulses with Double-Cladding Fiber-Based Nonlinear Chirped-Pulse Amplification

A compact 51.6-W, 26- μ J, Yb-doped all-fiber integrated CPA system through quasi-rectangular pulse pre-shaping

High Energy (>40 Nj), Sub-100 Fs, 950 Nm Laser for Two-Photon Microscopy.

1 kW, 10 mJ, 120 fs coherently combined fiber CPA laser system