Abstract:This paper introduces a compact picosecond laser system using tapered double cladding fiber-single crystal fiber hybrid amplification technology for the first time. By modifying the Ginzburg-Landau equation, we established a simulation model and designed a passive mode-locked picosecond oscillator based on a semiconductor saturable absorber mirror. The oscillator outputs laser with a pulse width of 7.75 ps, a center wavelength of 1030.55 nm, and a spectrum width of 0.58 nm. The seed laser is stretched and amplified by the all-fiber front stage, and then injected into the tapered double cladding fiber-single crystal fiber hybrid amplifier. The laser power is amplified from 820 mw to 103.1 W, obtaining a gain of 21 dB. We used zero-phonon line pumping technology in single crystal fiber amplifier to reduce the thermal effects caused by quantum loss, thereby increasing the length of the crystal and increasing the power loading capacity. We designed a single crystal fiber amplification module using Yb:YAG with 60 mm long, 1 mm diameter and a 1 at.% doping rate for the first time. Finally a hundred-watt level picosecond laser output with a repetition frequency of 26.33 MHz, an average power of 103.1 W, a pulse width of 244.72 ps, a spectrum width of 1.16 nm, and a beam quality of M2 x = 1.368 and M2 y = 1.511 was obtained. To the best of our knowledge, this is the highest picosecond laser output power for an all-fiber front-stage combined with a single-stage single crystal fiber amplifier.

High-power, 474 Fs, 31.12 MHz, All-Polarization-maintaining, 1560 Nm Fiber Laser System Based on the Chirped-Pulse Amplification

Sub-60-fs, Compact 1100-Nm Fiber Laser System Based on Double-Pass Pre-Chirp Managed Amplification.

Old Wavelength, New Performance: Hectowatt 200-μJ-level Femtosecond fiber CPA System at 1064 Nm

High-power 0.4-mJ picosecond CPA system based on an extra-large-mode-area triple-clad fiber

Generation of high-power 780 nm femtosecond pulses by an all-polarization-maintaining Er-doped fiber amplification system

All-PM Yb-doped mode-locked fiber laser with high single pulse energy and high repetition frequency

A large dispersion-managed monolithic all-fiber chirped pulse amplification system for high-energy femtosecond laser generation

High Energy and High Power Single Frequency 1572 nm Laser With an All-Fiber MOPA

396 MHz CPA femtosecond laser system based on a single crystal fiber rod-type amplifier

Hybrid fiber-single crystal fiber chirped-pulse amplification system emitting more than 1.5 GW peak power with beam quality better than 1.3

Compact, repetition rate locked all-PM fiber femtosecond laser system based on low noise figure-9 Er:fiber laser

Hybrid CPA system comprised by fiber-silicate glass fiber-single crystal fiber with femtosecond laser power more than 90 W at 1 MHz

PCF Based High Power Narrow Line Width Pulsed Fiber Laser

Investigations of the High-Power, Single-Frequency, Sub-Microseconds, 1548-nm Fiber Laser Based on the Optical Pulse Modulation

72-Kw High-Peak-power Linearly-Polarized Single-Mode Pulsed Fiber Laser with 80 Khz Repetition Rate and 4.5 Ns Duration

High-power chirped pulse amplification based on Yb-doped rod-type PCF and nonlinear amplifying loop mirror oscillator

140 kHz, 1.2 ps pulses from an all-PM Yb-doped fiber master oscillator-power amplifier

Tapered active fiber simultaneously enabled 141 W high average and 1.3 MW high peak power via all-fiber and polarization-maintained picosecond amplifier

Compact hundred-watt level picosecond laser system based on tapered double cladding fiber-single crystal fiber hybrid amplifier

All-Polarization-Maintaining, Mode-Locking Fiber Front-End Laser Delivering Both the Picosecond Seed Laser and the Femtosecond Seed Laser

High-peak-power nanosecond pulse laser at 915 nm based on all-fiber structure